Site work for a water / sewer project in Sheboygan, Wisconsin. Completed plans call for site work for a water / sewer project.

Separate sealed Bids are solicited for the following project: Project Name: 2,000,000 Gallon Standpipe Exterior Blast and Repaint with Containment Wet Interior Blast and Repaint And Miscellaneous Repairs Note: This project name shall be understood to include the entire scope of project as defined and detailed by these specifications. There will be no refund of handling charge for return of specification packages, or in the digital format. Format, Cost Bidding Documents (including 12 x 18 Drawings), $95.00 Flash Drive containing Bidding Documents in portable document format (PDF), $85.00 Electronic download of Bidding Documents by email (PDF), $75.00 For all further requirements regarding bid submittal, qualifications, procedures, and contract award, refer to the Instructions to Bidders, and if applicable Supplemental Instructions to Bidders, that are included in the Bidding Documents. An attempt will be made to do so; however, only registered plan holders will be notified by fax or email of expected addendum with short preparation times. Note 2: Prequalification of BIDDERS - Dixon Engineering will review qualifications of all Contractors and determine their status. Contractors will be prequalified for different sized tanks and towers based on experience, workmanship, successful Project completions with DIXON and Contractor's financial data. All information shall be submitted on an EJCDC Qualification Form 451. Any Contractor who has any projects in dispute or unfinished because of Contract problems will be considered NOT prequalified. Contractors wishing to be prequalified must submit their latest financial statement and a list of ten (l0) similar sized projects using similar coating systems. Failure to submit may result in rejection of bid. A prequalification status may be upgraded or downgraded during the course of the season, and possible during the Bidding period, as a result of new data submitted, resolution or origination of project conflicts. Disqualification will not result in the return of any handling fee for Bidding Documents. The Contractor shall abide by the following schedule: Commence work on or after May 30, 2020. Substantial Completion by October 30, 2020 including cure and disinfection time. The tank may be out-of-service a maximum of 80 days. As an alternate there is a line item for extra cost to be paid if work is to be performed with 60 days out-of-service. For liquidated damages, 80 days out-of service establishes Substantial Completion date. Liquidated damages at $1,250/calendar day shall apply after this date. Ready for Final Payment Date shall be thirty (30) days after date Substantial Completion was scheduled or adjusted by Change Order, or earlier if actual date. Liquidated damages after Ready for Final Payment Date of $250/day shall apply. Liquidated damages are cumulative if damages from Substantial Completion and Ready for Final Payment overlap. In addition, Special Damages may also apply per Bid/Agreement Form. Tank Information: The structure is a 2,000,000 gallon standpipe with an estimated sidewall height of 88 ft. and an estimated diameter of 60 ft. located on Georgia Ave. in Sheboygan, Wisconsin. The work includes: Exterior: Abrasive blast clean to a SSPC-SP6 commercial standard within containment and apply a four (4) coat zinc epoxy urethane fluoropolymer system. Wet Interior: Abrasive blast clean to a SSPC-SP10 near-white metal standard and apply a three (3) coat zinc epoxy system. Apply a polyurethane caulk to the roof lap seams. The cathodic protection system shall be removed and reinstalled by the owner's vendor, coordination and payment is the contractor's responsibility. Pit Piping: Abrasive blast clean to a SSPC-SP6 commercial standard and apply a two (2) coat epoxy system. Foundation: Repair grout and spalls. Abrasive blast clean and apply a two (2) coat epoxy system. Mixer: Install an air powered mixer in the wet interior. Repairs: 1) Pit welding. 2) Install sidewall manway. 3) Replace manway gasket on the sidewall manway. 4) Install a gasket on the roof hatch. 5) Anchor bolt repair. 6) Weld cathodic covers. 7) Install new sidewall ladder with platform. 8) Replace vent with a frost-free roof vent. 9) Install roof handrail with painter's rail. 10) Antenna equipment removal. 11) Install antenna conduit on the sidewall and outer section of the roof. The antennas and antenna cables will be removed from the tank by the antenna carrier prior to the start of the project. The antennas and antenna cables will be reinstalled by the carrier after the project is complete.