Renovation of a municipal facility in Pembroke Pines, Florida. Working plans call for the renovation of a 97,950-square-foot municipal facility.

The City of Pembroke Pines is seeking proposals from qualified firms, hereinafter referred to as the Contractor, to replace the roofs of various city buildings listed within in accordance with the terms, conditions, and specifications contained in this solicitation. This project is federally funded by the American Rescue Plan Act (ARPA) and thus will follow Federal Procurement guidelines. Please note: The City of Pembroke Pines has recently partnered with website to announce and distribute all formal solicitations, in excess of the $25,000 threshold, posted by the City of Pembroke Pines. As a result, the City will be transitioning from it's current e-Procurement Platform. SCOPE OF WORK PROJECT DETAILS (as required per each location) Verification of all dimensions, square footages, and quantities are the responsibility of the Contractor. The bid shall include pricing for a built-up roofing system. Vendor shall use CertainTeed roof materials or proven equal and receive approval from the city representative for such. All products must be Miami/Dade approved and installed in accordance with the current Florida Building Code. Where applicable, roof insulation shall be replaced with equal or greater quality and RValue. At no time shall the contractor uncover work which cannot be protected the same day. Contractor shall be responsible for removal and re-installation of all roof top equipment including but not limited to all skylights, satellite dishes, lightning protection, A/C equipment, and electrical/refrigerant penetrations where applicable. Remove all existing roof surfaces to supporting deck. Contractor responsible for cutting wall to remove old stucco stop at flashing. Repair any exposed damaged surfaces to include light weight concrete and stucco surfaces prior to installation of new roofing system. Contractor to provide price per foot on damaged lightweight concrete and stucco. For roofs that are not pre-tapered: Install all new insulation board (or lightweight concrete as needed) with a 1/4 " per foot required taper and any required crickets to allow proper drainage; there will be zero tolerance for ponding water. Include all seals required around existing vents, curbs, drains, scuppers or any other roof penetrations. Install 75# base sheet by mechanically fastening as per appropriate code requirements and engineer specifications. Install 2 plies of Flintglas ply VI hot mopped with asphalt. Install 1 ply of granulated fiberglass cap sheet. Install modified bitumen on all walls and flashings. Install all required membrane and sheet metal flashings in accordance with the local building code and the manufacturer's standard details. Flash all required curbs, parapet walls(up and over), mechanical curbs or other required areas. Install cantilever strip around all curbs and parapet walls. Install new retrofit drains. Secure all base flashings with proper sealant. Install termination bar around all curbs and wall flashing. Install all new surface mount stainless steel stucco stop where applicable. Fabricate and install all new stainless steel pitch pans throughout. Install expansion joints as required. Install all new 26 gauge stainless steel overflow scupper flashing Install all new 26 gauge stainless steel eave drip edge where applicable. Install all new 26 gauge stainless steel coping caps with proper PT wood nailers. Contractor shall replace all fascia and drip edge nailer with PT Wood. The pricing sheet contains a line item for the bidder to provide a cost per square foot to be used for plywood re sheeting replacement. Install walk pads from roof hatch to all A/C units. Where applicable, coping cap may not have exposed mechanical fasteners. Install all new goose necks to house refrigerant lines for A/C units where applicable. Install all new roofing equipment curbs where applicable. Install all new skylights where applicable. All equipment must be installed as per all governing code requirements. Contractor to provide a price per square foot to repair light weight concrete, metal deck and hidden stucco surfaces as needed. Contractor shall remove and reinstall gutters & downspouts as needed NOA No.: 17-0614.22 Questions Due Date: Nov 23rd 2021, 8:30 PM EST Intent to Bid Due Date: Nov 30th 2021, 2:00 PM EST The Closing Date has been extended until Tuesday, December 7th, 2021 at 2:00 p.m. Please remember you are still able to submit your proposals before the due date.