Renovation of a municipal facility in Beacon, New York. Completed plans call for the renovation of a municipal facility.

It is the bidder's responsibility to read the attached Bid Specifications and General Conditions which outline bidding rules of the City of Beacon. Upon submission of bid, it is understood that the bidder has read, fully understands and will comply with said specification requirements and general conditions. Service-Disabled Veteran-Owned Set Aside: No Minority Owned Sub-Contracting Goal: 0% Women Owned Sub-Contracting Goal: 0% Steep Slope Roofs (Approximately 9,000 square feet): Remove and replace steep slope roofs - approximately 9,000 square feet o Remove and dispose ofthe existing shingle roofing system down to the plywood substrate. Removal ofsolar panels by others will be done prior to shingle removal. o Remove and replace any damaged or deteriorated plywood substrate on a per-unit price basis per square foot o Leave gutter and leaders which are in good condition. o Install new 16 oz. cold-rolled copper drip edge at all eave and rake locations o Extend and match overhangs in front ofbuilding over flat roofs & extend gutter o Install a new GAF shingle roofsystem over the prepared roofsurface, to include: o Two (2) roll widths ofWeather Watch Ice and Water Shield (or equivalent) at all eaves and one (1) roll width at valleys and penetrations o Shingle-Mate (or equivalent) deck protection underlayment on the remainder of the roof deck. o New 16 oz. cold-rolled copper step and/or counter-flashing where required o Timberline HD (or equivalent) dimensional shingles, nailed six times per shingle. Color to be selected by the City o Cobra Ridge Vent (or equivalent) at ridge locations. o Cap off all hips and ridges with TimberTex (or equivalent) hip and ridge cap shingles o New copper-flanged neoprene boots at sanitary pipes. Flat Roofs (5 Areas/ Approximately 9,000 square feet): The City ofBeacon is soliciting qualified firms to install a new roof and related labor for removal of existing roof and installation of a new roof at the City ofBeacon Municipal Center. o Remove and replace steep slope roofs - approximately 9,000 square feet o Remove and dispose ofthe existing shingle roofing system down to the plywood substrate. Removal ofsolar panels by others will be done prior to shingle removal. o Remove and replace any damaged or deteriorated plywood substrate on a per-unit price basis per square foot o Leave gutter and leaders which are in good condition. o Install new 16 oz. cold-rolled copper drip edge at all eave and rake locations o Extend and match overhangs in front ofbuilding over flat roofs & extend gutter o Install a new GAF shingle roofsystem over the prepared roofsurface, to include: MUNICIPAL CENTER ROOF REPLACEMENT COB BID NO. 2022-001 o Remove and discard existing stone ballast from the roofsurface. City will provide location next to building within property line to place dumpster o Remove and dispose of existing base flashing with the roofing material o Cut existing EPDM field membrane into 10'xlO' grids o Install one layer of 1/2-inch high-density insulation over existing roofing o Insulation shall be mechanically attached at a rate of 1 fastener per 2 square feet o Fully adhere one ply of.060 unreinforced fire-rated black EPDM membrane in accordance with manufacturer's specifications. o Install new flashing system to include: o Flash all roof protrusions and wall base flashing with one ply of .060 EPDM membrane o At perimeter edges install EPDM flashing system in accordance with the manufacturer's specifications o Provide and install new cast iron drain clamping rings and dome strainers at five (5) existing drain locations o Shop-fabricate and install new 16 oz. cold-rolled copper counter-flashing to terminate top ofthe new base flashing below the existing counter-flashing o Furnish and install 24-gauge Kynar (or equivalent) coated steel snap-on fascia system with welded miters, in standard color, to meet ES-1 wind requirements. Patina Green or Dark Bronze color to match removed metal color. o Furnish and install concrete splash blocks with protection mats at upper shingle roof leader locations.