Renovation of a military facility in Versailles, Illinois. Completed plans call for the renovation of a military facility.

See the attached solicitation that has the SOW attached for more information This scope includes the replacement of EPDM (ethylene propylene diene) membrane roofs on the control station and the tainter gate control building at Peoria Lock and Dam and the control station at LaGrange Lock and Dam. A total of 3 buildings with membrane roofs will require the work. These buildings have historical significance and are required to be completed with in-kind materials. NAICS CODE: 238160 ESTIMATED RANGE: $25,000 to $100,000 COMPLETION DAYS: 120 Consecutive Calendar Days Total Small Business Set-Aside The actual RFQ will be published around the week of 3/24/2024 Locations: LaGrange Lock and Dam 714 1965E St. Versailles, IL 62378 Peoria Lock and Dam 1071 Wesley Rd Creve Coeur, IL 61610 Technical inquiries and questions relating to this solicitation are to be submitted to Joseph Porter at joseph.e.porter@usace.army.mil no later than 8 April 2024 at 10:00 AM Central. The contractor will have 120 days from the the date of the Notice to Proceed to complete the work. Please see SF1442 #11. *The value for this project is based on a financial range. The value is listed as the highest possible cost from the range provided by a stakeholder or official project document. This scope includes the replacement of EPDM (ethylene propylene diene) membrane roofs on the control station and the tainter gate control building at Peoria Lock and Dam and the control station at LaGrange Lock and Dam. A total of 3 buildings with membrane roofs will require the work. These buildings have historical significance and are required to be completed with in-kind materials. A. LaGrange Lock and Dam (priority): 1. Remove existing 1750 square feet of roofing material including the existing insulation and dispose of it a legal manner. 2. Provide and install two layers of 2.6" Polyisocyanurate Foam Board Insulation with an R-value of R30, to be fully foamed down to the existing concrete deck per state R-Value guidelines. 3. Provide and foam down 1/2 ":12" tapered insulation panels in between the existing roof drains for proper water drainage. 4. Provide and fully adhere a new EPDM membrane, with a minimum thickness of 60 mil. The lap seams shall be fabricated with 6" seam tape and stripped-in with self-adhering, semi-cured EPDM cover strips. 5. The existing metal coping shall be reused unless it is damaged beyond serviceability. In areas where new coping is required, it must match the existing coping. 6. Provide and install new roof drains that are compatible with EPDM membranes and have a clamping ring and a strainer. 7. Flash all walls and penetrations per manufacturer's specifications. 8. The existing metal edge is to be left in place and counter flashing will be fastened underneath the interior inside wall to terminate the new roofing membrane. 9. Provide a 20yr NDL manufacturer's warranty. 10. Price should include any permits required. 11. The contractor shall submit cut sheets and product data for the type of insulation, metal coping, and EPDM and how they intend to install it. B. Peoria Lock and Dam (both buildings): 1. Remove existing roofing material including the existing insulation and dispose of it a legal manner. Lock house square footage is 1750 and the tainter gate control building is 330 sqft. 2. Provide and install two layers of 2.6" Polyisocyanurate Foam Board Insulation with an R-value of R30, to be fully foamed down to the existing concrete deck per state R-Value guidelines. 3. Provide and foam down 1/2 ":12" tapered insulation panels in between the existing roof drains for proper water drainage. Provide and fully adhere a new EPDM membrane, with a minimum thickness of 60 mil. The lap seams shall be fabricated with 6" seam tape and stripped-in with self-adhering, semi-cured EPDM cover strips. 5. The existing metal coping shall be reused unless it is damaged beyond serviceability. In areas where new coping is required, it must match the existing coping. 6. Provide and install new roof drains that are compatible with EPDM membranes and have a clamping ring and a strainer. 7. Flash all walls and penetrations per manufacturer's specifications. 8. The existing metal edge is to be left into place and counter flashing will be fastened underneath the interior inside wall to terminate the new roofing membrane. 9. Provide a 20yr NDL manufacturer's warranty. 10. Price should include any permits required. 11. The contractor shall submit cut sheets and product data for the type of insulation, metal coping, and EPDM and how they intend to install it. Locations: A. LaGrange Lock and Dam 714 1965E St. Versailles, IL 62378 B. Peoria Lock and Dam 1071 Wesley Rd Creve Coeur, IL 61610