Renovation of an educational facility in Sea Girt, New Jersey. Completed plans call for the renovation of a educational facility.

Chiller Replacement At Sea Girt Elementary School for the Sea Girt Borough Board of Education 451 Bell Place Sea Girt, New Jersey 08750 Neither the Owner, nor the Architect will assume any responsibility for bids mailed or misdirected in delivery. No bid may be withdrawn for a period of sixty (60) calendar days from the opening of the bids. Should you have any questions, please contact the Architect's office at 866-974-7666. The Owner reserves the right to reject all bids pursuant to applicable law and waive any immaterial informality in the bidding process in accordance with the law. The Contract, if awarded, shall be awarded to the lowest responsible bidder whose bid is responsive in all material respects to the bid requirements. No bid shall be deemed accepted until the adoption of a formal resolution by the Owner. All bidders must use and complete all bid forms provided in the manner designated and must comply with all requirements contained in the instructions and specifications. Bids shall be placed in a sealed envelope with the name of the project clearly marked on the front of the envelope and accompanied by a bid guarantee in the form of a Certified Check, Cashier's Check, or Bid Bond in the amount of Ten Percent 10% of the bid, but not more than $20,000. Due to the special nature of the work involved that can only be seen by an in-depth visitation, the attendance of all the bidders is requested and STRONGLY ENCOURAGED as an integral and important element of the bidding process so that all bidders have an equal understanding of the scope of work involved. SINGLE-OVERALL CONTRACT BID Sealed Bid Proposals shall be received as follows: The bidder shall be classified by the New Jersey Department of the Treasury, Division of Property Management and Construction (DPMC) in the following trade(s): C032 - HVACR Subcontractors named in the Form of Bid Proposal for Structural Steel, Plumbing, Heating Ventilating and Air Conditioning, and/or Electric, who perform any work on the Project must be prequalified prior to the submission of bids, pursuant to the State of New Jersey Division of Property Management and Construction (DPMC). Each bid must be accompanied by proof of Contractor's DPMC classification status. For projects with NJSDA funding the New Jersey Schools Development Authority NJSDA prequalification process requires that each bid must be accompanied by proof of Contractor's DPMC classification status with NJSDA's School Finance and Construction Program. Bidders are required to comply with requirements of N.J.S.A. 10:5-1 et seq., "The Law Against Discrimination," and affirmative action, N.J.S.A. 10:5-31 et seq. and N.J.AC. 17:27-1 et seq. All bidders and their subcontractors shall be registered with the New Jersey Department of Labor and Workforce Development, pursuant to the Public Works Contractor Registration Act, N.J.S.A. 34:11-56.48 et seq. It is encouraged that all bids be accompanied by a Certificate issued by the New Jersey Department of Labor and Workforce Development, pursuant to the Public Works Contractor Registration Act to the Bidder and all subcontractors named in the Contractor's bid. If not included with the bid, these documents must be submitted prior to award. Pursuant to N.J.S.A. 52:32-44, it is encouraged that all bids include a New Jersey Business Registration Certificate issued by the New Jersey Department of Treasury, Division of Revenue of the Bidder and include that of all subcontractors named in the Contractor's bid. If not included with the bid, these documents must be submitted prior to award. A. Clean surfaces thoroughly and correct defects prior to application. B. Prepare surfaces using the methods recommended by the manufacturer for achieving the best result for the substrate under the project conditions. C. Remove or mask surface appurtenances, including electrical plates, hardware, light fixture trim, escutcheons, and fittings, prior to preparing surfaces for finishing. D. Seal surfaces that might cause bleed through or staining of topcoat. E. Remove mildew from impervious surfaces by scrubbing with solution of tetra-sodium phosphate and bleach. Rinse with clean water and allow surface to dry. All questions must be answered, and the data given must be clear and comprehensive.