Site work and paving for a road / highway in Lexington, Kentucky. Completed plans call for site work for a road / highway; and for paving for a road / highway.

Question Deadline 02/18/2026 at 3:00 PM ET Questions about projects during the advertisement should be submitted in writing to the Division of Construction Procurement. This may be done by email to kytc.projectquestions@ky.gov The deadline for posting answers will be Eastern Daylight Time, the day preceding the Letting. Scott County Fbp 0644(102) : Frankfort - Lexington Road (I-64) - 105b00082n Bridge 105b00082n Over I-64 at Mp 67.52 Asphalt Pavement & Roadway Rehab. Syp No. 07-10059.00. Scott County Nhpp 0644 (100) : I-64 Pavement Rehabilitation Scott County I-64 Pavement Rehabilitation Scott County, a Distance of 3.89 Miles. Asphalt Pavement & Roadway Rehab. Syp No. 07-20049.00. Woodford County Fbp 0644(102) : Frankfort - Lexington Road (I-64) - 102B00024L Bridge 120b00024l Over Elkhorn Creek at Mp 67.10 Asphalt Pavement & Roadway Rehab. Syp No. 07-10059.00. Woodford County Fbp 0644(102) : Frankfort - Lexington Road (I-64) - 120B00022L Bridge 120b00022l Over Us 421 at Mp 64.98. Asphalt Pavement & Roadway Rehab. Syp No. 07-10059.00. Woodford County Fbp 0644(102) : Frankfort - Lexington Road (I-64) - 120B00022R Bridge 120b00022r Over Us 421 at Mp 65.00. Asphalt Pavement & Roadway Rehab. Syp No. 07-10059.00. Woodford County Fbp 0644(102) : Frankfort - Lexington Road (I-64) - 120B00024R Bridge 120b00024r Over Elkhorn Creek at Mp 67.10 Asphalt Pavement & Roadway Rehab. Syp No. 07-10059.00. Woodford County Nhpp 0644 (099) : I-64 Pavement Rehabilitation Woodford County I-64 Pavement Rehabilitation Woodford County, a Distance of 2.25 Miles. Asphalt Pavement & Roadway Rehab. Syp No. 07-20048.00. The Department Will Only Accept Bidder Registration Forms From Contractors Who Are Prequalified in the Work Categories of the Particular Project. Registration Will Be Closed at 3:00 Pm on the Day Preceding the Letting. KYDOT - Call 200 - Asphalt Pavement & Roadway Rehabilitation - I-64 Except as specified in these notes, all work shall consist of furnishing and installing all materials necessary for permanent data acquisition station equipment installation(s) and shall be performed in accordance with the current editions of: o The Contract o Division of Planning Standard Detail Sheets o Kentucky Transportation Cabinet, Department of Highways , Standard Specifications for Road and Bridge Construction o Kentucky Transportation Cabinet, Department of Highways, Standard Drawings o National Fire Protection Association (NFPA) 70: National Electrical Code o Institute of Electrical and Electronic Engineers (IEEE), National Electrical Safety Code o Federal Highway Administration, Manual on Uniform Traffic Control Devices o American Association of State Highway and Transportation Officials (AASHTO), Roadside Design Guide . o Standards of the utility company serving the installation, if applicable The permanent traffic data acquisition station layout(s) indicate the extent and general arrangement of the proposed installation and are for general guidance. Any omission or commission shown or implied shall not be cause for deviation from the intent of the plans and specifications. Information shown on the plans and in this proposal and the types and quantities of work listed are not to be taken as an accurate or complete evaluation of the material and conditions to be encountered during construction. The bidder must draw his own conclusion as to the conditions encountered. The Department of Highways (Department) does not give any guarantee as to the accuracy of the data and no claim will be considered for additional compensation if the conditions encountered are not in accordance with the information shown. If any modifications of the plans or specifications are considered necessary by the Contractor, details of such modifications and the reasons, therefore, shall be submitted in writing to the Engineer for written approval prior to beginning such modified work. The Contractor shall contact all utility companies and the district utility agent prior to beginning construction to insure proper clearance and shielding from existing and proposed utilities. The Contractor shall use all possible care in excavating on this project so as not to disturb any existing utilities whether shown on the plans or not shown on the plans. Any utilities disturbed or damaged by the Contractor during construction shall be replaced or repaired to original condition by the Contractor at no cost to the department. If necessary , to avoid existing utilities, the Contractor shall hand dig areas where poles or conduit cross utilities. This work shall consist of removing and re-installing a high tension cable-rope HTC median barrier. The existing cable-rope barrier system is a Brifen Wire Rope Safety Fence (WRSF). This item shall consist of furnishing, installing, relocating, operating, servicing, and removing various components of a portable, quickly deployable, real -time automated ITS queue warning alert system (PQWAS), in accordance with the standard specifications and this special provision. The Contractor shall also provide the maintenance of the complete system for the duration of the project or as directed by the Project Engineer . The Department is willing to look at different technologies (i.e. allow the use of crowd sourcing data to be used in lieu of the portable radar sensors). Any changes to the below requirements must be submitted and approved by the Engineer. Perform all work in accordance with the Kentucky Transportation Cabinet, Department of Highway's Standard Specifications for Road and Bridge Construction and applicable Supplemental Specifications, the Standard Drawings, (current editions), this Note and Attached Detailed Drawings. Section references are to the Standard Specifications. This work consists of the following: (1) Furnish all labor, materials, tools, and equipment, (2) Cleaning and Painting and (3) Any other work specified as part of this contract. Perform all work in accordance with the Kentucky Transportation Cabinet, Department of Highway's Standard Specifications for Road and Bridge Construction and applicable Supplemental Specifications (Current Editions), this note and attached detailed drawings. Section references are to the Standard Specifications. This work consists of the following: (1) Furnish all labor, materials, tools, and equipment; (2) Remove existing joint seal; (3) Install joint seal as specified (4) Maintain and control traffic; and (5) Any other work specified as part of this contract.