Renovation of a multi-residential development in Baltimore, Maryland. Completed plans call for the renovation of a one-unit multi-residential development.

The Contractor shall supply all labor, material, supervision, equipment, insurance, permits including U&O (Unit of Occupancy Permit), and all other incidentals required to complete the work items listed as requested by HABC, in accordance with all applicable federal, state and local regulations. Questions Due Date: Jun 5th 2026, 2:00 PM EDT The Contractor shall supply all labor, material, supervision, equipment, insurance, permits including U&O (Unit of Occupancy Permit) and all other incidentals required to complete the work items listed below as requested by HABC, in accordance with all applicable federal, state and local regulations. 1501 Presser Ct General: 1. Remove and properly dispose of all Trash, Furniture and Miscellaneous Items in the Unit. 2. Replace closet shelving/closet rod as necessary 3. Final Cleaning of Entire Unit to Make Ready for Occupancy. Bathrooms: 1. Remove existing sink and vanity, supply and install new Vanity Cabinet w/ Vanity Bowl, faucet and stainless steel 1-1/4" drain line. 2. Clean existing toilet and replace round toilet seat 3. Remove existing, supply and install New Medicine Cabinet with Mirror 4. Remove existing, supply and install all new bathroom Accessories, Non-UFAS 5. Clean existing shower wall, tub/ w. tub faucet, tub spout and showerhead, Resurface existing tub 6. Remove existing shower rod, supply and install new shower rod 7. Remove existing (1) 6 panel doors. Supply and install (1) 6 panel doors with privacy passage set. Kitchen: 1. Remove existing rangehood, supply and install Broan #4100 range hood (Black) 2. Remove existing kitchen cabinets, Supply and Install HUD severe use base and wall cabinets 3. Remove existing countertop, supply and install new countertops. 4. Remove existing kitchen faucet, supply and install new Delta faucet 5. Remove existing kitchen sink drain line, supply and install new stainless steel 1-1/2" (inch) drain line. 6. Remove existing, supply and install laundry hookup box and hot /cold water valves. 7. Remove existing electrical raceway, install new electrical raceway with a junction box installing a GFI at least Bedroom # 1: 1. Supply and install new vertical window blinds (1) 2. Clean exterior and interior of heating convector of any debris. 3. Clean window frame including sills and wells (Lead Testing) and window glass. 4. Paint existing Closet shelf and pole. 5. Remove existing interior 6 panel doors (2), supply and install two (2) 6 panel interior doors with new passage sets (non - privacy).Livingroom: 1. Remove existing window blinds, supply and install new window blinds (2) 2. Clean window frame including sills and wells (Lead Testing) and window glass 3. Remove existing receptacle covers, supply and install new receptacle covers 4. Clean exterior and interior of heating convector of any debris. 5. Clean window frames including sills and wells (Lead Testing) and window glass Hallway 1. Paint both existing closet shelves and pole. 2. Remove existing 6 panel doors, supply and install new 6 panel doors Mechanical / Plumbing: 1. Check and Inspect Gas Distribution (Stove) for service and repair any leaks. 2. Water Distribution (Bathroom & Kitchen) for leaks, repair leaks throughout whole unit 3. Inspect and Repair (if necessary) Drain, Water & Vent (Bathroom and Kitchen, toilets) Electrical: 1. Remove existing cover plates, supply and install all Switches / Receptacles and metal cover plates. 2. Remove existing raceways, supply and install new raceways throughout entire unit 2. Check Electric Service Panel for Gaps/Missing Breakers/Doors. 3. Remove existing light fixtures, supply and install LED integrated light fixtures in common areas, kitchen, living room and bathroom. 4. Install 10 yr. sealed smoke detectors in bedroom 5. Install combination smoke / carbon monoxide detectors on 1 st Floor common area.