Renovation of a municipal facility in Edmonton, Alberta. Completed plans call for the renovation of a municipal facility.

Objective: Conversion of change room to office space at the Edmonton NFLS building. Work includes: Safely demolish and dispose of ceramic floor and wall tiles, ceilings, interior drywall partitions and doors, flooring, millwork, shower, toilet, sink and counters (fully gut the space). Cut, terminate, and make safe all services no longer needed in the room, including electrical, sanitary, venting, and water. Supply and install a new T-bars, ceiling tiles and two in-ceiling LED lights throughout. Patch plumbing holes through the floor. Supply and install carpet tiles and rubber wall base (style and colour to be determined by the Technical Authority). Patch, tape and sand all drywall and make ready for painting. Supply and paint all walls (paint type and colour to be determined by the Technical Authority). Add additional electrical outlets according to code as needed to ensure adequate supply. Relocate and adjust sprinkler heads to suite the new layout. Poly hoarding installed to mitigate dust transfer. Work of this Contract comprises conversion of existing Change Room 310 to office space at the Edmonton RCMP facility, 15707 118 Avenue NW, Edmonton, Alberta T5V 1B7, including architectural, mechanical, electrical, controls, fire suppression and fire alarm modifications indicated in the Contract Documents. The Contractor shall provide all labour, materials, equipment, coordination, testing and related Work required for a complete installation. The scope includes, but is not limited to, the following: .1 Demolish existing interior partitions, wall finishes, shower finishes and associated components as indicated on the Architectural Drawings; .2 Remove existing shower floor tiles, concrete topping, curbs and associated materials as required, and prepare the substrate to provide a level surface suitable for the new floor finish; .3 Restore wall areas affected by removal of the existing sink, millwork, countertop, paper towel dispenser and recessed waste bins. Infill existing wall recesses and openings to provide a continuous finished wall surface flush with adjacent construction and matching the adjacent wall assembly and acoustic requirements. Patch and finish surfaces in accordance with the Architectural Drawings and Division 09; .4 Provide new suspended acoustic T-bar ceiling in accordance with the Architectural Drawings. Coordinate final ceiling elevation with existing and new mechanical, electrical, fire protection and other above-ceiling services, .5 Remove existing floor finishes and underlying materials as indicated, prepare and level the substrate as required, and install new carpet tile flooring and base in accordance with the Architectural Drawings and Division 09; .6 Provide acoustic wall treatment, batt insulation, acoustic sealing and related work in accordance with the Architectural Drawings and Division 09 to maintain the indicated acoustic performance of the Room 310 wall assembly; .7 Prepare and paint new and affected existing wall and ceiling surfaces in accordance with the Room Finish Schedule, Architectural Drawings and Division 09; .8 Provide new 120 V receptacles and communication/data outlet rough-ins as indicated on Drawing E-01, including associated conduit, wiring, boxes and accessories; .9 Install new BGIS-supplied LED light fixtures matching the existing fixtures in type and appearance, complete with associated wiring, switching and accessories, as indicated on Drawing E-01; .10 Provide new emergency lighting for Room 310 as indicated on Drawing E-01 and specified in Section 26 52 13.13; .11 Provide one new combination horn/strobe notification appliance in Room 310 and connect to the existing fire alarm system as indicated on Drawing E-01 and specified in Section 28 46 00; .12 Provide electrical connections and branch-circuit modifications as indicated on Drawing E-01; .13 Provide new return-air grille, matching the existing Room 310 return-air grille size and type, as indicated on Drawing M-01. Existing return-air ductwork shall remain. .14 Provide one new hardwired DDC-compatible thermostat for Room 310 and integrate it with the existing BAS/DDC system serving the third-floor RTU in accordance with Drawing M-01 and Section 25 30 00. Field verify the existing BAS/DDC control architecture and applicable thermostat control function prior to programming; .15 Remove and cap existing plumbing supply and drainage lines serving the sink, toilet and shower as indicated on Drawing M-01 and specified in Division 22; .16 Modify the existing sprinkler system as indicated on Drawing M-01, including relocation of one existing sprinkler head and removal and capping of one existing sprinkler branch connection. Maintain required sprinkler coverage in accordance with NFPA 13 (2025) and applicable AHJ requirements; .17 Perform all associated demolition, patching, restoration, coordination, testing and commissioning required for a complete installation in accordance with the Contract Drawings and Specifications. BGIS reserves the right to reject our submission should BGIS fail to receive the required documentation. Question Acceptance Deadline Oct 16, 2026 02:00 PM MDT Questions are submitted online Yes Official bid documents must be obtained from www.merx.com and bid submissions must be done through the Merx platform.