Renovation of a swimming pool in Missoula, Montana. Completed plans call for the renovation of a swimming pool.

Quote attn: Marty Rehbein 435 Ryman Street Missoula, Montana 59802 rehbeinM@ci.missoula.mt.us. This project consists of construction services to remove and dispose of the existing pool liner and provide and install the replacement liner as well as associated site work located at Splash Montana, at Playfair Park in Missoula, Montana. SCOPE OF PROJECT This project consists of the design, procurement and installation of a new high grade (60 mils) commercial swimming pool vinyl liner system for the 50m Astral pool at Splash Montana at 3001 Bancroft Street in Missoula, Montana. Work is to include: 1. PREFERRED: All work to be completed and ready for pool fill by April 20th, 2022. 2. A pre-installation site evaluation shall be completed by the Supplier to identify any site issues that may need to be addressed above and beyond the items in this contract. 3. Removal and disposal of the existing PVC liner up to the joint where the pool liner meets the gutter liner (about 3 inches into the gutter system). (See Fig. 1). 4. When removing the old pool liner, to remove all floor mounted plastic inlet diffusers and replace with new ones plus provide 30 extra diffusers to keep for when the new ones are damaged over the winters. 5. When removing the old pool liner, to save & reinstall with the new liner the (4) Neptune-Benson Aegis 30x30 VGB rated main drain covers and (4) metal drain grate adaptors - these drain grates are marked as eligible for use until 2025. 6. Broom clean pool basin floors and walls to remove dirt and debris. Prepare pool basin floors and walls as required to ensure a sanitary environment and watertight installation. 7. All pool penetrations shall be terminated with compression flanges or other parts necessary to make a complete watertight installation. Extra flanges and other parts necessary for maintaining the watertight installation shall be provided for future onsite repairs by the City. 8. Apply adhesive as required according to liner manufacturer's specifications. 9. Replacement liner shall be minimum of 60 mils (1.5 mm) thickness. 10. Complete additional perimeter caulking, details work, and finish work to make a complete watertight installation. 11. The liner used on the entry ramp surface, and the top edge of the pool basin shall be of an anti-slip version, with a textured finish to reduce slips. (See fig. 2) 12. The textured, anti-slip liner that is installed on the top edge of the pool basin shall meet the US Swimming requirement and extend no less than .8 meters (2 feet 7.5 inches) below the water surface. 13. The preferred color of the liner will be light blue, however white will be accepted. 14. The color of the lane line markers, targets, lane numbers, depth signs and other warnings will be black. 15. When replacing the pool liner to include lane line markers to provide and designate (8) length-wise (Long Course) 50m lanes and 10 width-wise (Short Course) 25 yard lanes. 16. The lane line anchors for the 8 Long Course lanes are already existing and located in the desired locations. 17. The lane line anchors for the 10 short course lanes do not already exist. There are anchors for 8 lanes, but they are not in the desired location. The City would like these anchors removed and replaced with anchors to allow for 10 short course lanes, each one being 8 feet wide. 18. When replacing the pool liner we are requesting that lane designation numbers be placed on the bottom of the pool in each of the (8) designated Long Course lap lanes, oriented so as to be readable from the end of the pool at the shallow and the deep ends. 19. Long Course Lane designations will be numbered from right to left (south to north) as the swimmers stand facing the course at the deep end wall. 20. When replacing the pool liner we are requesting that the pool bottom lane marker lines shall end with a distinctive cross line 1.0 meters (3 feet 4 inches) long and the same width as the bottom marker. The line, including the cross line, shall terminate 2.00 meters (6 feet 7 inches) from each end wall. 21. When replacing the pool liner we are requesting that the pool bottom lane line markers for the (8) 50m length lanes shall be no less than 10 inches wide, unbroken from shallow end to deep, be placed in the middle of each racing lane and shall be black in color. 22. For the (10) 25 yd width lanes we are requesting that they be broken lines and black in color. 23. When replacing the pool liner we are requesting that there be a cross on the wall of each of the (8) 50m Lanes and each of the (10) 25 yd lanes, at both ends for a total of (16) crosses for the 50m lanes and (20) crosses for the 25 yd lanes. 24. End Wall Targets shall be flush, non-slip targets in the shape of a cross and shall be the same width as the lane bottom markers. They shall be in the center of each lane on each end wall and shall extend at least 3 feet 4 inches below the level of the water surface. 25. The existing pool has hook attachments for 9 lane lines on the two short sides (9 x 2) and 8 lane lines on the two long sides (8 x 2). (See Fig. 3) The City would like these replaced with a better lane line attachment system designed for overflow gutters, such as the S.R Smith Lane Line Anchor Stainless Steel 8 Inch (prod #:17-61-200) or comparable and to add 3 additional lane attachments on the two long sides to enable a total of 11 width lanes. 26. Install Depth/No Diving markers and Pool safety markings as per Montana State Rule for Pools. 27. Replace the perimeter pvc pool gutter grating with a system similar to that already installed. (See Fig. 4) Provide spare pvc gutter grating pieces for future replacement of damaged pieces (minimum 30 feet of grating and 4 corner pieces). 28. Clean the site suitable for pool filling and perform final inspection. 29. Please declare the duration of the warranties for the Pool Membrane and any Welds.