Renovation of a civil project in New Berlin, Texas. Completed plans call for the renovation of a water / sewer project.

The scope of work includes but is not limited to: 1. Wagner Booster Pump Station: a. Modification of existing main breaker to replace trip 1600A unit with 2500A trip unit, replace 1600A current sensors with 2500A rated current sensors b. Demolition of existing ATS c. Demolition of existing ductbank (including conduit & wire) to generator from ATS and wire from ATS to bus transition section. d. Temporary relocation of generator and demolition of existing generator pad e. Installation of new non-SE rated ATS with enclosure, ductbank from new SE rated ATS (including conduit & wire), new wire from ATS to MCC, new generator concrete pad. f. Installation of new generator 120V circuits (battery blanket heaters and receptacles) g. Replacement of circuit breaker feeding ancillary generator circuit panelboard and replacement of ancillary generator circuits panelboard main circuit breaker. h. Installation of all required control wiring associated with generator, and ATS to the site PLC. i. Inclusive of all testing and power system studies. 2. Leissner Booster Pump Station: a. Demolition of existing ductbank (including conduit & wire) to generator from ATS, wire from ATS to MCC. b. Temporary relocation of generator and demolition of existing generator pad c. Installation of new pull box on exterior or the electrical building, new overhead conduit & wire runs from existing SE rated ATS to new pull box and new ductbank (including conduit & wire) from pull box to generator, new wire from ATS to MCC, new generator concrete pad. d. Demolition of existing 208V generator engine block heater and replacement with a 240V engine block heater with same wattage e. Installation of new generator 120V circuits (battery blanket heaters and receptacles) f. Replacement of existing generator ancillary circuit panelboard and installation of new transformer and MCC feeder breaker to serve the proposed generator ancillary circuit panelboard. g. Installation of all required control wiring associated with generator, and ATS to the site PLC. h. Inclusive of all testing and power system studies. 3. Dead Man Well: a. Demolition of existing ATS and main breaker b. Installation of new ATS and main breaker c. Installation of new generator 120V circuits (battery blanket heaters and receptacles) d. Installation of all required control wiring associated with generator, and ATS to the site PLC. e. Inclusive of all testing and power system studies. 4. Wells Ranch WTP - Service No.1 a. Demolition of existing wire/conduit previously installed to and from main breaker/ATS/generator (non-utility wire) b. Demolition of the existing main breaker section c. Demolition of existing ATS d. Temporary relocation of generator and demolition of existing generator pad e. Modification of existing Siemens switchboard line-up to decouple the main breaker section from the distribution sections. f. Installation of new main breaker section g. Installation of new MLO section at the end of switchboard line up h. Installation of new wire and cable tray system from new main breaker to ATS, from ATS to new MLO section. i. Installation of new wire and cable tray system from new ATS to new pull box on exterior of the building. j. Installation of new ductbank from pull box to the existing 1600kW generator k. Installation of new dry-type transformer and panelboard for new circuits to generator panels l. Installation of new generator 120V circuits (battery blanket heaters and receptacles) m. Installation of all required control wiring associated with PQM, generator, and ATS to the plant PLC. n. Inclusive of all testing and power system studies. 5. Wells Ranch WTP - Service No. 2 a. Demolition of existing wire/conduit previously installed to ATS/generator b. Demolition of the existing empty pull section adjacent to the switchboard c. Demolition of existing ATS d. Temporary relocation of generator and demolition of existing generator pad e. Modification of existing Eaton switchboard line up to decouple the main breaker section from the distribution section. f. Installation of new MLO section at the end of switchboard line up g. Installation of new wire and cable tray system from existing main breaker to ATS, from ATS to new MLO section. h. Installation of new wire and cable tray system from new ATS to pull box on exterior of the building. i. Installation of new ductbank from pull box to the existing 1250kW generator j. Installation of new generator 120V circuits (battery blanket heaters and receptacles) k. Installation of all required control wiring associated with PQM, generator, and ATS to the plant PLC. l. Inclusive of all testing and power system studies. The deadline to ask questions is 2/14/2025 5:00 PM CST