Demolition, site work and addition to an educational facility in Hinsdale, Illinois. Completed plans call for the addition of a 12,600-square-foot educational facility; for the demolition of a educational facility; and for site work for a educational facility.

PROJECT DESCRIPTION Project to include an Athletic Training Facility Addition (Approximately 12,600 SF) and all related accommodations including but not limited to: demolition of portion(s) of existing building; complete design and construction of new building; all MEPFPIT systems with integration into existing; and required site work. a. Demolition i. Demolish all site/building items as required to provide for new work. Items to be demolished (but not limited to): 1. See concept plan and existing drawings for context, but not exact requirements. The contractor is responsible for all coordination of demolition and reconstruction of all existing items affected by new work. ii. Locate all existing utilities. Connect to existing as required for new work. Any abandoned utilities to be fully removed. b. New Construction: i. Approximately 14,000 SF Athletic Training Facility Addition, including the renovation of the existing training facility known as the Bouchard Center and all associated site work: 1. Building Program (Square footages are approximates): a. 8000 SF Weight Room b. 650 SF Team Room c. 140 SF Storage Room d. 1500 SF Training Room with Wet areas. Isolate hydrotherapy and wet areas with curb or partial/full wall and provide floor drain. Area to remain accessible. e. Water Station. Adjacent Hydrotherapy. f. 300 SF Coaches Office g. 150 SF Office h. 2-3 Accessible Toilet Rooms (adjacent and accessible to exterior) i. 375 SF Small Team Room j. 220 SF Lockable Storage k. Mechanical l. Circulation/Egress from existing building. 2. Future Addition Alternate: Provide a concept that would allow for a 2nd story to be added as a future construction project. Include line-item cost relative to the increased structural capacity design. Account for circulation implications of a future 2nd floor addition and extension of all building systems. 3. Structural System: a. Option 1: CMU Bearing Wall with Brick Veneer Cavity Wall and Steel roof Framing. b. Option 2: Steel Framed Structure with Glass and Curtain wall . The facade can be a combination of solid wall, glass and glazing. c. Alternate: Provide cost information and feasibility for the structural system to accommodate future 2nd story. 4. Existing Windows for Contractor Use (Optional depending on design): a. DeSCo, i85 Series b. (16) 67"H x 37"W 5. Finish materials: a. Exterior Face Brick i. ASTM C216, Type FBS, Grade SW. ii. Manufacturer: Summit Brick Company iii. Color and Texture: Color - 506 Ginger, Texture - Vertical Scratch iv. Nominal Size: Modular. v. Special Shapes: Molded units as required by conditions. b. Acoustical Ceilings i. Acoustical Units - General: ASTM E1264, Class A 1. Size: 24 by 24 inches. 2. Thickness: 3/4 inches. 3. Composition: Water Felted. 4. Light Reflectance: No less than 0.8 5. NRC Range: 0.70 6. Ceiling Attenuation Class (CAC): .35 min. 7. Additional Performance: Humidity and sag resistant. Anti-mold/Anti-microbial. 8. Edge: Square 9. Color: White 10. Pattern: Non-directional fissured. 11. Exposed Steel Suspension System: White, 15/16, Heavy-Duty Galvanized Steel. Suspension system and Acoustical Units to be of the same manufacturer. c. Resilient Flooring i. Luxury Vinyl Tile (LVT-1): Printed film type, with transparent or translucent wear layer. 1. Manufacturer: Tandus Centiva 2. Minimum Requirements: Comply with ASTM F1700: Class III, Type B 3. Plank Size: 9 by 36 inches. 4. Wear Layer: Thickness: 0.020 (20 mil). 5. Total Thickness: 0.120 inch. 6. Pattern: color Beam. 7. Color: Gray. 8. Texture: Quarry. 9. Installation Direction: Coordinate with Owner 10. Location(s): Corridor, Offices and Team Rooms d. Tile i. Glazed Porcelain Floor and Wall Tile, Type T-5: ANSI A137.1, Standard Grade. 1. Size: 12 by 24 inch, nominal. 2. Thickness: 5/16" inch. 3. Edges: Cushioned. 4. Surface Finish: Unpolished. 5. Wet Dynamic: Coefficient of Friction (ANSI A137.1, DCOF Accutest): 0.42. 6. Color: Degrees Silver 7. Trim Units: As required by design 8. Products: Daltile - Volume 1 9. Location(s): Toilet Rooms ii. Glazed Wall Tile, Type T-11: ANSI A137.1, Standard Grade. 1. Size: 4 by 12 inch, nominal. 2. Thickness: 5/16" inch. 3. Edges: Cushioned. 4. Surface Finish: Polished. 5. Wet Dynamic: Coefficient of Friction (ANSI A137.1, DCOF Accutest): 0.42. 6. Color: Sonic White 7. Trim Units: As required by design 8. Products: Daltile - Color Wheel Collection Linear. 9. Location(s): Toilet Rooms e. Rubber Athletic Flooring i. Athletic Flooring - RBR-1 1. Manufacturer: Mondo Indoor Sport: Sport Impact 10 MM 2. Color: Custom with Branding/Logo inlay at all weight rack stations. 3. Location(s): Weight Room and Training Room f. Indoor Turf i. Manufacturer: FieldTurf ii. Color: Green iii. Location(s): Weight Room g. Epoxy i. Manufacturer: Sherwin-Williams ii. Color: Selected from Full Range iii. Slip Resistant iv. Anti-microbial v. Location(s): Hydrotherapy and Water Station h. Logos and Branding i. Include Allowance for District Logos and Branding to be incorporated into finishes. i. Acoustic Treatment i. Spray Applied Acoustical Insulation ii. Manufacturer: Internation Cellulose Corporation iii. Product: K13 Sound Absorption Spray 6. Door Hardware a. Hinges: Stanley b. Continuous Hinges: Stanley c. Locksets: Best 45H (Coordinate Function with Owner) d. Cylinders: Best Peaks (Coordinate with Owner) e. Exit Devices: Von Duprin f. Closers: LCN g. Key Fob Integration into all access points h. Stops: Trimco i. Threshold & Gasketing: Nation Guard j. Flush Bolts: Trimco 7. Roofing a. SBS, Modified Bitumen i. 20 Year Warranty ii. Completely replace the existing roof of existing building to be renovated and tie into new addition. iii. Provide roof access from renovated space or addition. iv. Primary roof drainage to be tied into the existing storm water drainage system. Extension of system required for addition. v. Metal work: Color to be selected by owner from manufacturer's full range 8. Owner Provided Equipment a. See the following exhibits: i. List of District Provide Equipment ii. Weight Room Equipment Proposal b. Contractor to coordinate equipment space clearances and infrastructure requirements in design. 9. Contractor Provided Equipment a. All Stainless Steel Cabinets b. All Stainless Steel Shelving c. All Built-in Cabinets and Counters 10. MEPFPIT a. See SD86 HCSC - Athletic Training Facility - MEPFP Narrative 11. Sustainability a. The district is interested in incorporating sustainable design principles into the Building Addition. 3. Level of Design to be included within Proposal a. Site Plan b. Proposed Floor Plan - Plan does not need to match concept plan. c. 3D Renderings of Athletic Training Facility Addition Scope (Interior and Exterior) d. Product Data and Warranties for all proposed products e. Provide physical samples of proposed products. f. Manufacturer Standard Technical Details for all proposed products g. Detailed Schedule of Values i. Provide line items for each product ii. Include Material and Install iii. Include bond, insurance, overhead and profit h. Detailed Proposed Schedule i. Include durations of install required for each product i. Complete Sub-Contractor List