Renovation of an educational facility in Centre, Alabama. Completed plans call for the renovation of a educational facility.

Package A - (Single Ply) Roofing Work at Cherokee County Career Tech Package B - (Metal Roof Overlay) Roofing Work at Sand Rock School and Spring Garden High School A. Extent of demolition work is shown on drawings, as well as all items necessary to complete new work indicated on plans. B. Schedule of Demolition Work: Demolition includes but is not limited to the following: 1. Any damage to existing facilities at the site after the Contractor takes possession shall be repaired by this Contractor at his expense. 2. Contractor shall replace grass/sod damaged during the construction. Fill in ruts caused by equipment with topsoil and grass over to match existing conditions. 3. As indicated on the Drawings. 4. All other items indicated required to be demolished to complete new work. A. The work under this section consists of all preformed metal roofing, underlayment, ridge vent system, sheet metal, roof drainage accessories and all related items necessary to complete the roofing system work indicated on the drawings and herein specified including but not limited to the following: 1. Formed Roof Panels for Standing Seam Installation 2. Underlayment. 3. Workmanship 4. Inspection of Surfaces 5. Protection 6. Delivery, Samples and Shop Drawings A. The roofing contractor shall be fully knowledgeable of all requirements of the contract documents and shall make themselves aware of all job site conditions prior to the bid that will affect their work. B. Provide all labor, material, tools, equipment, and supervision necessary to furnish and install a 60 mil white reinforced TPO (Thermoplastic Polyolefin) or a 60 mil PVC (polyvinyl chloride) membrane. A. Extent of each type of flashing and sheet metal work is indicated on drawings and by provisions of this section. B. Types of work specified in this section include the following: 1. Metal Counter Flashing and Base Flashing. 2. Metal Diverters. Verify location with Architect for all entry doors. 3. Exposed Metal Trim Units 4. Eave Strip/Drip Edge 5. Fascia 6. Coping 7. Scuppers and Leader Heads 8. Gutters 9. Downspouts 10. Elastic flashing. 11. Elastic roof/wall expansion joint systems. C. Integral masonry flashings are specified as masonry work in sections of Division 4. A. The extent of each form and type of joint sealer is indicated on drawings and by provisions of this section. B. The applications for joint sealers as work of this section include the following: 1. Joints (Exterior). 2. Flashing Joints. C. General Performance: Except as otherwise indicated, joint sealers are required to establish and maintain airtight and waterproof continuous seals on a permanent basis, within recognized limitations of wear and aging as indicted for each application. Failures of installed sealers to comply with this requirement will be recognized as failures of materials and workmanship. A. Extent of painting work is indicated on drawings and schedules, and as herein specified including accent painting. B. Work includes painting and finishing of interior and exterior exposed items and surfaces throughout project, except as otherwise indicated. 1. Surface preparation, priming and coats of paint specified are in addition to shop-priming and surface treatments specified under other sections of work. C. Work includes field painting of exposed bare and covered pipes, conduits and ducts (including color coding), and of hangers, exposed steel and iron work, and conduits and primed metal surfaces of equipment installed under mechanical and electrical work, except as otherwise indicated. D. "Paint" as used herein means all coating systems materials, including primers, emulsions, enamels, stains, sealers and fillers, and other applied materials whether used as prime, intermediate or finish coats. E. Surfaces to be Painted: Except where natural finish of material is specifically noted as a surface not to be painted, paint exposed surfaces whether or not colors are designated in "schedules". Where items or surfaces are not specifically mentioned, paint the same as similar adjacent materials or areas. If color or finish is not designated, Architect will select these from standard colors or finishes available. F. Following categories of work are not included as part of field-applied finish work. 1. Pre-Finished Items: Unless otherwise indicated, do not include painting when factory-finishing or installer finishing is specified for such items as (but not limited to) metal toilet enclosures, prefinished partition systems, acoustic materials, elevator entrance doors and frames, elevator equipment, and finished mechanical and electrical equipment, including light fixtures, switchgear and distribution cabinets. 2. Concealed Surfaces: Unless otherwise indicated, painting is not required on surfaces such as walls or ceilings in concealed areas and generally inaccessible areas, foundation spaces, furred areas, utility tunnels, pipe spaces, duct shafts and elevator shafts. 3. Finished Metal Surfaces: Unless otherwise indicated, metal surfaces of anodized aluminum, stainless steel, chromium plate, copper, bronze and similar finished materials will not require finish painting. 4. Operating Parts: Unless otherwise indicated, moving parts of operating units, mechanical and electrical parts, such as valve and damper operators, linkages, sinkages, sensing devices, motor and fan shafts will not require finish painting. G. Following categories of work are included under other sections of these specifications. 1. Shop Priming: Unless otherwise specified, shop priming of ferrous metal items is included under various sections for structural steel, metal fabrications, hollow metal work and similar items. 2. Unless otherwise specified, shop priming of fabricated components such as shop-fabricated or factory-built mechanical and electrical equipment or accessories is included under other sections of these specifications.