Renovation of a military facility in Billings, Montana. Completed plans call for the renovation of a military facility.

Three projects are to be performed at federal facilities in Montana and include restoration, office construction, and HVAC system installation. Work at the Billings USMS facility involves stainless steel restoration, including removing scratches from stainless steel benches and walls in areas to be verified during a contractor, USMS, and GSA walk-through, along with painting. Work at the Bozeman FSA facility requires construction of a new wall with metal studs, installation of a matching door and frame, extending the wall to the deck above, installing matching baseboard, adding electrical receptacles if required by code, repairing or replacing carpet as needed, painting the entire room with low VOC paint to match existing finishes, repairing the affected ceiling grid, relocating fire sprinklers according to code, and adjusting HVAC ceiling penetrations as needed. Work at the Bozeman FWS facility includes installing a heat removal system for ultra-low temperature freezers to maintain room temperatures between 64.4F and 89.6F, with the contractor to investigate and propose either a new exhaust system with a fresh air supply duct or a ductless split-system AC unit with a fresh air supply, along with pricing. All work requires the contractor to provide all labor, materials, equipment, and supervision; comply with applicable codes and standards; submit a detailed cost breakdown and proposed solutions; maintain OSHA and GSA safety standards; coordinate access during business hours; and ensure personnel meet HSPD-12 badge requirements. Project Location Battin US CH 2601 2nd Ave N. Billings, MT 59101 Building Manager: Mike Buhman Phone: 406-839-1930 Bozeman FB/PO 10 E Babcock St. Bozeman, MT 59715 Building Manager: Mike Buhman Phone: 406-839-1930 Project Points of Contact Contracting Officer: Unknown Project Manager: Mike BuhmanPhone: Phone: 406-839-1930 PROJECT SCOPE Project Summary The General Services Administration, Region 8, is performing a RWA project to: 1. Billings USMS: Refresh and repaint the cellblock stainless steel and paint. (RWA#3721836) 2. Bozeman FSA: Build a wall and door to create an office. No wiring/outlets required (unless by code). Spaceiscurrently an "alcove" that would be sealed off. (RWA#3752889) 3. Bozeman FWS: Either a new exhaust system or a no duct split system AC unit will be needed to removetheexcess heat from the room. Currently there is no fresh air provided to the space and will need to beadded. (RWA# 3727940) Project Objectives The contractor shall provide labor, materials, equipment and supervision necessary to performthe following: Billings USMS: Refresh and repaint the cellblock stainless steel and paint. (RWA#3721836) Remove scratches in stainless steel benches, walls, etc. in the cellblock and interview areas as follows: 2ndfloor: C1, C2, C32nd floor: P1, P2, P3, P4, I1 5TH floor: 5C1, 5C2 Exact locations of scratches/damage will be verified by contractor, USMS and GSA via a walk-throughof the spaces. Repaint doors and doorframes in the following areas (paint specifics TBD):2nd floor: P1 (door frame), P2 (door and frame), P3 (door and frame), P4 (inside of door) 5th floor: 5C2 (door) Bozeman FSA Wall addition (RWA#3752889): Enclose an alcove area and make a private office for Lance W. in FSA, west end on the 5th floor. Build new wall to enclose the alcove. Utilize metal studs and 5/8" drywall. Add a door and frame tomatchothers in the space for type, size and color. Wall will extend to the deck above. Install baseboard to match existing in the space on the new wall. Install electrical receptacles in new wall if code requires it. If code does not, no outlets are needed. Repair/replace carpet as needed to build new wall. Paint entire room with low VOC paint to match existing paint. Repair ceiling grid that was affected during the wall construction. As code requires, move fire sprinklers for the new office space. As needed, move any hvac ceiling penetrations for the office. Bozeman FWS Freezer Room B26 HVAC - (RWA#3727940) To ensure the proper operation of the ultra-low temperature freezers and maintain a secure environment, an improved heat removal system is required. Potential solutions include the installation of a newexhaust system or a ductless split-system air conditioning unit. The freezers cause heat gain in the room that needs to be removed. According to the operation andmaintenance manual the room temperature for the ultralow temp freezers ambient operational rangeshould be 64.4F to 89.6F Either a new exhaust system or a ductless split system AC unit will be needed to remove the excessheat from the room. Fresh air will need to be supplied through a new added duct. Contractor shall investigate and submit their proposed solution along with project pricing.