Site work and renovation of an educational facility in Rocanville, Saskatchewan. Completed plans call for the renovation of a 7,175-square-foot educational facility; and for site work for a educational facility.

Removal and replacement of 7,175 sq. ft. (666m2) of the existing shingle roof system. Project: Rocanville School 1002 Francis Avenue Rocanville, SK SOA OH5 For questions, contact engineering@rmiseng.ca. This project is being professionally managed on behalf of South East Cornerstone Public School Division by RMIS. Documents are available at www.sasktenders.ca 1 Roof Section 4B: .1 Remove and store the existing roof hatch. .2 Remove and store for reuse the existing roof top HVAC units, exhaust fans, and other roof top equipment. Test and document operability prior to removal. connections. .3 Remove and discard the existing roof vents. .4 Remove and store the existing powered roof vents. .5 Remove and discard the existing ducting. .6 Remove and discard the existing conduit and wiring. .7 Remove and discard the existing equipment curbs. .8 Remove and discard the existing gutters and downspouts. Properly terminate all .9 Remove and discard the existing decommissioned curbs, pipe penetrations and other abandoned equipment. .10 Remove and discard the existing cladding. .11 Remove and discard the existing shingles and underlayment down to the deck. .12 Remove and discard the existing base flashings and stripping. .13 Remove and discard the existing rough carpentry as required by the contract documents. .14 Remove and discard the existing metal flashings and trim. .15 Remove and discard the existing sealant and accessories. .16 Furnish and install new fall arrest anchors. .17 Inspect the deck, walls and curbs for damage or other issues. Ensure the deck is dry before installation of new materials. 18 Infill holes and openings in the deck left from the removal of abandoned equipment and penetrations. .19 Extend all pipe penetrations. .20 Furnish and install new nailers and blocking. .21 Furnish and install new wood framed curbs, walls and prefabricated curb support nailers. .22 Furnish and install new composite panel on all parapets, curbs and walls. .23 Furnish and install new SBS base sheet composite panel. .24 Furnish and install new SBS cap sheet membrane. .25 Furnish and install new SBS base flashings on all parapets, walls and curbs. .26 Furnish and install new pipe penetration flashings. .27 Furnish and install new sheet metal flashings and trim. .28 Reinstall the existing roof top HVAC equipment. .29 Test and document equipment operability. .30 Furnish and install new weather tight stainless steel fasteners to secure the roof top fans, vents and other equipment to the curbs. .31 Furnish and install new vents. .32 Reinstall existing powered vents. .33 Furnish and install new ducting. .34 Furnish and install new conduit and wiring. .35 Reinstall the existing roof hatch. .36 Furnish and install new gutters and downspouts. .37 Furnish and install heat trace. .38 Furnish and install new concrete splash blocks below all downspouts on the roof and on the ground. .39 Install new sealant and accessories to ensure the roof system remains watertight. .2 Roof Section 12: .1 Remove and discard the existing roof vents. .2 Remove and discard the existing gutters and downspouts. 3 Remove and discard the existing decommissioned curbs, pipe penetrations and other abandoned equipment. .4 Remove and discard the existing shingles and underlayment down to the deck. .5 Remove and discard the existing base flashings and stripping. .6 Remove and discard the existing rough carpentry as required by the contract documents. .7 Remove and discard the existing metal flashings and trim. .8 Remove and discard the existing sealant and accessories. .9 Inspect the deck, walls and curbs for damage or other issues. Ensure the deck is dry before installation of new materials. .10 Infill holes and openings in the deck left from the removal of abandoned equipment and penetrations. .11 Furnish and install new nailers and blocking. .12 Furnish and install new underlayment. .13 Furnish and install new asphalt shingles. .14 Furnish and install new sheet metal flashings and trim. .15 Furnish and install new weather tight stainless steel fasteners to secure the roof top fans, vents and other equipment to the curbs. .16 Furnish and install new vents. .17 Furnish and install new gutters and downspouts. .18 Furnish and install new soffits. .19 Furnish and install new concrete splash blocks below all downspouts on the roof and on the ground. .20 Install new sealant and accessories to ensure the roof system remains watertight