Renovation of an educational facility in Washington, New Jersey. Completed plans call for the renovation of a 16,630-square-foot, one-story above grade educational facility.

As of May 15, 2024, this project has been awarded. The original bid listing is included below for informational purposes. Roof Replacement at Flocktown and Kossmann Elementary Schools State Project Number: 27-5520-030-23-1000 (FES), 27-5520-080-23-1000 (KES) Bidders shall direct questions in writing to Matthew Jenkins at the office of Parette Somjen Architects L.L.C. by mail, by facsimile at 973.586.2401, or by email at mjenkins@planetpsa.com. Location FLOCKTOWN ELEMENTARY SCHOOL 90 FLOCKTOWN ROAD LONG VALLEY, NEW JERSEY 07853 KOSSMAN ELEMENTARY SCHOOL 90 FLOCKTOWN ROAD LONG VALLEY, NEW JERSEY 07853 Bids must be accompanied by bid security in the form of (1) a bid bond or certified or cashier's check payable to the Washington Township Board of Education equal to 10% of the amount of the bid, but in no case to exceed $20,000.00 per N.J.S.A. 18A:18A-24, and (2) Certificate of Consent of Surety per N.J.S.A. 18A:18A-25. The Board of Education reserves the right to reject any non-responsive bids or all bids pursuant to N.J.S.A. 18A:18A-22. No bid may be withdrawn for a period of sixty (60) days after the opening date. The Contract will be awarded to the lowest responsible bidder as defined in N.J.S.A. Questions will be considered only up until the inquiry deadline stated in the Instructions to Bidders. The scope of this project includes, but is not limited to, roof replacement. The Contract Documents define the full project scope. Bids, utilizing the bid forms as prepared by the Architect, may be submitted in person, by mail, or delivery service prior to that time. No bids will be received by facsimile or electronic transmission. Delivery by the time stipulated above of any bid submitted by mail or delivery service is done so at the sole risk of the Bidder. It is expressly understood that the Bidder is responsible for getting the bid proposal to the Business Administrator prior to the time and date set for the bid opening. Any bid received after the bid submission time deadline will be returned unopened. Question due date December 1, 2023 ASE SHEET & BASE SHEET FASTENERS FOR NAILABLE ROOF DECK (TECTUM) A. Base Sheet Membrane: ASTM D4601, Type II glass fiber base sheet 1. (Basis of Design) GAF-GLAS #75 or Perma-ply 28 glass fiber base sheet shall be mechanically fastened to the lightweight concrete/gypsum roof decks with OMG Roofing Products' 1.8 OlyLok base sheet fastener as required per field pullout tests. At a minimum, the base sheet and all fasteners shall be installed per this specification, and manufacturer's recommendations, whichever is more stringent, to resist uplift pressures as calculated in accordance with ASCE 7-16 and listed above under Section 2.1, and contractor confirmed field tested pullout values. 2. Approved equal in accordance with specification section 01 60 00 "Product Requirements" 2.13 INSULATION FASTENERS FOR WOOD AND METAL DECKS A. Fasteners: Factory-coated steel fasteners and metal plates complying with corrosion-resistance provisions in FM Approvals 4470, designed for fastening substrate board to roof deck. 1. OMG Standard roof insulation screw fastener with corrosion resistant coating as recommended by roof membrane manufacturer. 2. Approved fasteners with three (3) inch coated disc to meet or exceed the specific project wind uplift requirements listed in Section 2.1 "Design and Performance Criteria" of Division 7 Section "SBS Bituminous Membrane Roofing". Length as required to penetrate roof deck per the screw manufacturers recommendation or one (1) inch if not listed. 2.14 INSULATION ADHESIVE A. Insulation Adhesive: Insulation manufacturer's recommended adhesive formulated to attach roof insulation to base sheet mechanically attached to tectum deck or to another insulation layer as follows: i. ASTM D312, Type IV Special Steep Asphalt.