Site work for a religious / funeral development in Crownpoint, New Mexico. Completed plans call for site work for a religious / funeral development.

The Navajo Nation Division of Community Development (DCD) Capital Projects Management Department (CPMD) on behalf of the Crownpoint Chapter, invites qualified contractors to submit proposals for the construction of a perimeter fence for the Crownpoint Chapter Community Cemetery in Crownpoint, New Mexico. This Request for Proposal (RFP) accounts for a preliminary evaluation of the offeror(s) qualifications, proposed product, site knowledge, and project schedule. The Navajo Nation is not bound to enter a contract under this RFP and may issue a subsequent RFP for the same services at its own discretion. Deadline to Submit RFP Questions February 20, 2025 @ 5:00 PM (MT) Technical questions about the request for proposals, scope of services Ricky Begay, Engineering Technician Capital Projects Management Dept. Navajo Nation Division of Community Development P.O. Box 1510 Window Rock AZ 86515 Email: rickyrbegay@nndcd.org The CPMD is seeking proposals from responsible, qualified and independent contractors to supply and install a permanent no-climb, perimeter fence around the Crownpoint Chapter Cemetery Site. The perimeter fence/wall will surround the 40.46+- acre (5,568+- linear feet) Crownpoint Chapter Cemetery Site tract. The 40.46+- acres includes burial plots for civilian and veteran community members. The Chapter has the following objectives for this project: Define boundaries and channel access and egress; Provide visual barriers, supports security and safety; Deter and delay intrusion and trespassing; Provide security; Provide cost-effective method of protecting facilities; Offeror(s) shall furnish all labor, material, and equipment to complete the work as outlined further in this section and as indicated on the Schedule Attachment E. Unless otherwise stated, all content outlined in this section should be considered as incidental to the schedule. A. Minimum Specifications for Perimeter Fence Length of Fence Perimeter shall be based on lengths as shown in Attachment A - Legal Boundary Survey a. Fence Fabric i. 6' high x 11-1/2 gauge Galvanized Chain Link Fabric (2-1/4 x 11-1/2 x 72 GAW), KK, 50' roll b. Framework i. 1-5/8" x 21' Swedged End HF20 (0.085 wall) ii. 2" x 8' Galvanized HF20 cut post (Line Post) iii. 4" x 12' Galvanized HF40 cut post (Gate Post) iv. 2-1/2" x 8' Galvanized HF20 cut post (Corner Post) c. Post Fittings i. Eye Top Loop Cap 2" x 1-5/8" - Pressed Steel ii. Post Cap 2-1/2" Aluminum Dome iii. Post Cap 4" Aluminum Dome iv. 2-1/2" Galvanized Beveled Brace Band - Round v. Rail End Cap 1-5/8" Brace Combo Pressed Steel vi. 3/16" x 5/8" wide x 72" long Tension Bar vii. Tension Band 2-1/2" Beveled 12-gauge x 7/8" viii. Carriage Bolt/Hex Nut 5/16" x 1-1/4" d. Wire and Ties i. Tie Wire 1-5/8" Aluminum Pig-Tail 9 gauge (6") - Bag of 100 ii. Tie Wire 2" Aluminum Pig-Tail 9 gauge (6-1/2") iii. 7-gauge Galvanized Spiral Tension Wire - 1000' roll iv. 11-gauge Steel Hog Ring B. Minimum Specifications for Primary Support Columns / Posts a. Post holes will be drilled and all excess dirt material from the holes will be removed. Holes will be cleaned out and depth to be confirmed on all at 24", typical, 12"x 48" for cantilever posts. b. Setting Posts and Concrete: All gate entrances and the 6 corners of the perimeter to have concrete columns. This phase to commence after the preparation is completed. All terminal, gate and line posts set in holes. Concrete to be mixed and poured at terminal, and gate posts first, line posts to be set, aligned and plumbed at all locations. c. Concrete to be 4,000 PSI, 4" slump with air and fibers. The forms to have chambers on all corners. d. Curing Stage/Concrete Pad: Offeror will allow a two-day curing time for the posts. e. Line Post distance an average of 10 feet. Depending on the terrain.