Site work and new construction of a pre-engineered storage facility in Sykesville, Maryland. Completed plans call for the construction of a pre-engineered storage facility; and for site work for a pre-engineered storage facility.

Purchase and Installation of Pole Barn Building at the Hodges Facility. Question Deadline 05/15/2025 at 4:00 PM ET Pole Barn Building at the Hodges Facility, located at 5630 Hodges Road, Eldersburg MD 21784 The Carroll County Office of Procurement, in cooperation with the Bureau of Utilities, is soliciting bids for the purchase and installation of a pole building at the Bureau of Utilities' Hodges Facility, located at 5630 Hodges Road, Eldersburg, MD 21784. A. The building shall be a forty-eight (48) foot wide by fifty (50) foot deep by sixteen (16) foot high post frame package. B. The building shall have three (3) - fourteen (14) foot wide by fourteen (14) foot high garage doors with openers on the forty-eight-foot-wide side facing towards the Hodges Facility yard. The spacing dimensions of the garage door side of the building shall be as follows: a. Building corner b. 1 foot spacing c. 14-foot-wide garage door d. 2 foot spacing e. 14-foot-wide garage door f. 2 foot spacing g. 14-foot-wide garage door h. 1 foot spacing i. Building corner C. When facing the garage door side of the building from the yard, there shall be one (1) standard sized exterior door located on the left fifty-foot-deep side of the building, as close to the front corner of the building as possible. A. The building shall be constructed at a location within the Hodges Facility as designated by County staff. B. Any general site preparation work and grading will be performed by County staff. C. The Contractor will be responsible for any excavation work for post holes and footings. D. Under no circumstanceswill any support postsforthe building interfere with vehicle entry or full vehicle use of the building. E. Material Package 1) Pre-Engineered Wood Trusses (4/12 Pitch, 4' O/C) 2) 4.5 x 5.25 Glu-Lam Post 3 Ply Eave Posts (8' O/C) 3) 4.5 x 5.25 Glu-Lam Post 3 Ply Gable Posts (10' O/C) 4) 2 x 6 Treated Skirt Boards (1 Row) 5) 2 x 6 Wall Girts (36" O/C) 6) 2x4 Roof Purlins (24" O/C) 7) 2 x 12 Double Top Girt Truss Carrier 8) Roof to be insulated with vapor barrier and include a ridge vent. 9) 0.60 Sq. Ft. Ceiling Insulation 10) 1.25 Sq. Ft. Wall Insulation 11) Beige G100 Steel Siding 12) Galvanized G100 Steel Roof 13) Painted Steel Liner Panel on Walls 14) Painted Steel Ceiling Liner Panel 15) One Concrete Pad per Post Hole . Doors 1) Three 14-foot by 14-foot insulated steel wrapped insulated overhead doors with openers. 2) One standard insulated exterior entry door. G. Soffit 1) 10-inch eave overhang, 10-inch gable overhang aluminum soffit. Gutter 1) Standard aluminum gutter and downspouts. A minimum of one downspout at each corner of the building. I. Fasteners. 1) 1/2 inch Siding Screws for Steel Wall Panel 2) 1 inch Neoprene Siding Screws for Steel Roof Panel 3) 3-1/2 inch Galv. Pole Barn Nails for Truss Carrier 4) 3-1/2 inch Galv. Pole Barn Nails for Skirt Board 5) Galvanized Steel Framing Nails