Site work for a detention facility in Jennings, Louisiana. Completed plans call for site work for a detention facility.

Furnish & Install 10ft Security Chain Link Fence Furnish & Install 8ft Perimeter Chain Link Fence Furnish & Install Gates to existing Chain Link Fence A bid bond will be required with bid submittal if bid is over $50,000. Question Deadline 02/10/2026 at 9:00 AM CT For questions related to the electronic bidding process, please call Central Bidding at 225-810-4814 . Formal questions for bid shall be directed to the Parish Administrator in written form and emailed to: ben@jdppj.net . PROJECT SUMMARY: Furnish & Install security chain link fence and associated gates according to the project specifications and layout of the attached plan sheets. Project location is at the Jefferson Davis Parish Consolidated Jail at 1704 Shankland Ave, Jennings, LA 70546. 8FT PERIMETER FENCE Furnish all materials, equipment, and labor to install 8ft Perimeter Fence with the following specifications: -To the maximum extent practicable, the fence shall follow the natural contours of the existing ground, with the bottom of the fence installed approximately no more than 2 inches above finished natural grade. - All metal & fence components shall be hot dipped galvanized. - All line post shall be 2.0-inch sch 40 cemented in an 6-inch augured hole 3ft deep, spaced 10ft apart. - All corner/terminal/gate posts shall be 2.5-inch sch 40 cemented in an 8-inch augured hole 4ft deep. -The bottom 6 inches of all line and corner post may be driven in in lieu of cement. -Chain-link shall be 2-inch fabric, 8ft tall, and 9 gauge. - Fence shall include 1-1/4 inch sch 40 continuous top brace rail. -Fence shall include a 3-strand barbed topper, 12-gauge, class 3, 4 point heavy. - Fence shall include 7-gauge bottom tension wire. - Wire fabric shall be supported to post and top rail every 18 inches minimum. GATES A1, A2, & B FOR 8FT PERIMETER FENCE Furnish all materials, equipment, and labor to install Gates on the 8ft Perimeter Fence with the following specifications: - All metal & fence components shall be hot dipped galvanized. - All gate sizes shall be as specified by the attached plan sheets. - Gates themselves shall be framed with 1.5-inch pipe sch 40 with a center horizontal support and a tensile diagonal support. - Gates shall be double swing with tamper resistant hinges. - Gates shall have tamper resistant latch, ready for customer supplied padlock, with said padlock accessible from both sides of gate. Typical gate latch forks that are susceptible to rotating will not be allowed. -Gates must have 2-inch fabric, 8ft tall, and 9 gauge. - Gates must have 3-strand barbed topper, 12-gauge, class 3, 4 point heavy. 10FT SECURITY FENCE Furnish all materials, equipment, and labor to install 10ft Security Fence with the following specifications: - To the maximum extent practicable, the fence shall follow the natural contours of the existing ground, with the bottom of the fence installed approximately 1 inch above finished natural grade. - All metal & fence components shall be hot dipped galvanized. - All line post shall be 3-inch sch 40 cemented in an 8-inch augured hole 4ft deep, spaced 8ft apart. - All corner/terminal/gate posts shall be 3-inch sch 40 cemented in an 8-inch augured hole 5ft deep. - The bottom 6 inches of all line and corner post may be driven in in lieu of cement. - Chain-link shall be 2-inch fabric, 10ft tall, and 9 gauge. - Fence shall include 1-1/4 inch sch 40 continuous horizontal brace rail positioned within the top 15 inches of fence. - Fence shall include a 3-strand barbed topper, 12-gauge, class 3, 4 point heavy (to mount razer coil). - Fence shall include continuous prison-grade razor coil meeting state penitentiary design standards, consisting of 30-inch diameter maze-style (MZ-31L) stainless steel barbed tape, triple-clipped at all overlaps, continuously mounted on barbed-wire topper, with no gaps permitted. - Fence shall include 7-gauge bottom and top tension wire. - Wire fabric shall be supported to post and top rail every 14 inches minimum. GATES D FOR 10FT SECURITY FENCE Furnish all materials, equipment, and labor to install Gates on the 10ft Security Fence with the following specifications: - All metal & fence components shall be hot dipped galvanized. -All gate sizes shall be as specified by the attached plan sheets. - All gates shall include a header designed to match the adjacent fence chain-link and razor coil. The header shall include 1-1/4 inch Schedule 40 pipe at both the top and bottom. The header assembly shall be included in the applicable gate bid item. - Gates themselves shall be framed with 1.5-inch pipe sch 40 with a center horizontal support and a tensile diagonal support. - Gates shall be double swing with tamper proof hinges. - Padlock Gates (as noted on attached plan sheets) shall have tamper proof latch, ready for customer supplied padlock, with said padlock accessible from both sides of gate. - Keyed Gates (as noted on attached plan sheets) shall be manufactured to install owner supplied mounting box to accept owner supplied keyed latch (AIRTEQ 5080). Fabrication will also include installation of owner supplied latch plate (AIRTEQ Fence Gate Keeper) to be installed on latch side gate post. Reference attached AIRTEQ Spec Sheet (AIRTEQ 5080 FENCE GATE MOUNTING). Due to the tight tolerances (0.25 inches) required by the AIRTEQ 5080 keyed latch system, it is highly recommended that the latch plate be welded onsite to the latch side gate post. All such welds must have 3 coats of cold galvanize. -Gates shall be installed with clearances not exceeding 2 inches between the gate and adjacent gate posts or overhead headers. GATES F FOR 10FT SECURITY FENCE Furnish all materials, equipment, and labor to install Gates on the 10ft Security Fence with the following specifications: - All metal & fence components shall be hot dipped galvanized. -All gate sizes shall be as specified by the attached plan sheets. - All gates shall include a header designed to match the adjacent fence chain-link and razor coil. The header shall include 1-1/4 inch Schedule 40 pipe at both the top and bottom. This header shall also be hinged and utilize same hinge and latch as gate below. This header will only be opened for emergencies to allow in emergency vehicles. The header assembly shall be included in the applicable gate bid item. - Gates themselves shall be framed with 1.5-inch pipe sch 40 with a center horizontal support and a tensile diagonal support. - Gates shall be double swing with tamper proof hinges. - Padlock Gates (as noted on attached plan sheets) shall have tamper proof latch, ready for customer supplied padlock, with said padlock accessible from both sides of gate. - Keyed Gates (as noted on attached plan sheets) shall be manufactured to install owner supplied mounting box to accept owner supplied keyed latch (AIRTEQ 5080). Fabrication will also include installation of owner supplied latch plate (AIRTEQ Fence Gate Keeper) to be installed on latch side gate post. Reference attached AIRTEQ Spec Sheet (AIRTEQ 5080 FENCE GATE MOUNTING). Due to the tight tolerances (0.25 inches) required by the AIRTEQ 5080 keyed latch system, it is highly recommended that the latch plate be welded onsite to the latch side gate post. All such welds must have 3 coats of cold galvanize. -Gates shall be installed with clearances not exceeding 2 inches between the gate and adjacent gate posts or overhead headers. GATES C & E TO BE ADDED TO EXISTING 12FT SECURITY FENCE Furnish all materials, equipment, and labor to install Gates to the existing 12ft Security Fence with the following specifications: - All metal & fence components shall be hot dipped galvanized. - All gate sizes shall be as specified by the attached plan sheets. -Gate openings shall be framed with 3-inch sch 40 post cemented in an 8-inch augured hole 5ft deep on each side. Note, an existing 4-inch post can substitute on one side. - The bottom 6 inches of gate post may be driven in in lieu of cement. - Above said gates shall include a header and a continuous razor coil (existing fence). Top and bottom of header shall include a 1-1/4 inch sch 40 pipe. -Gates themselves shall be framed with 1.5-inch pipe sch 40 with a center horizontal support and a tensile diagonal support. - Gates shall be double swing with tamper proof hinges. - Padlock Gates (as noted on attached plan sheets) shall have tamper proof latch, ready for customer supplied padlock, with said padlock accessible from both sides of gate. - Keyed Gates (as noted on attached plan sheets) shall be manufactured to install owner supplied mounting box to accept owner supplied keyed latch (AIRTEQ 5080). Fabrication will also include installation of owner supplied latch plate (AIRTEQ Fence Gate Keeper) to be installed on latch side gate post. Reference attached AIRTEQ Spec Sheet (AIRTEQ 5080 FENCE GATE MOUNTING). Due to the tight tolerances (0.25 inches) required by the AIRTEQ 5080 keyed latch system, it is highly recommended that the latch plate be welded onsite to the latch side gate post. All such welds must have 3 coats of cold galvanize. Gates shall be installed with clearances not exceeding 2 inches between the gate and adjacent gate posts or overhead headers.