Site work for a service station / car wash facility in West Palm Beach, Florida. Completed plans call for site work for a service station / car wash facility.

Description: The Florida Department of Transportation, Palm Beach Operations Center, located at 7900 Forest Hill Blvd, West Palm Beach, Florida 33413. hereinafter referred to as "Department", seeks to obtain the services of a certified licensed and insured electrical contractor to perform all labor, materials, equipment, and incidentals necessary to perform the replacement of the existing above ground fuel storage tanks. All questions must be submitted to D4.designbuild@dot.state.fl.us by (or before) Tuesday, March 31, 2026 PREQUALIFICATION: Each bidder shall submit a current license issued by the State of Florida (specify type license required for t he work) and, if a Florida Corporation, a copy of the Corporate Charter as prequalification of their eligibility with the bid document to the Department of Transportation, Contracts Administration Office: Florida Department of Transportation - District Four, 3400 West Commercial Boulevard, Fort Lauderdale, FL 33309. If the bid amount exceeds $100,000, the bidder must provide with the bid, a Bid Guaranty of five percent (5%) of the actual total bid in the form of a certified check, cashier's check, treasurer's check, bank draft of any national or state bank, or a surety Bid Bond made payable to the Department of Transportation. If the contract award amount exceeds $100,000, both a Performance Bond and a Labor and Material Payment Bond of 100% each of the contract sum are required at the time of award FDOT - Palm Beach Operations Center Replacement of Above Ground Fuel Storage Tanks The work specified under this Contract shall consist of providing all labor, materials, equipment, and incidentals necessary to perform the replacement of the existing above ground fuel storage tanks at the Florida Department of Transportation, PALM BEACH OPERATIONS CENTER. Scope of Services 4.1 Furnish Labor, Equipment and Materials for the Following Scope of Work: 4.1.1 Mobilize men and equipment to the job site. 4.1.2 Disconnect and safe off the fuel system electric. 4.1.3 Evacuate the existing product lines by blowing the product back into the tanks. 4.1.4 Disconnect the existing aboveground piping from the existing fuel tanks. Remove and Replace Sump. 4.1.5 Remove and dispose of all remaining gasoline and diesel fuel left inside the tanks. 4.1.6 Clean and vapor free the existing tanks ensuring they are safe. 4.1.7 Transport and dispose of the (2) existing 10,000 gallon tanks after cleaning. 4.1.8 Furnish and install (2) 10,000 gallon cylindrical aboveground UL 2085 Fireguard tanks designed for gasoline and diesel fuel. 4.1.9 Each tank interior will be painted with an epoxy liner and each exterior will be painted with an epoxy primer and white urethane. The tanks must come with a 30-Year warranty. 4.1.10 Furnish and install on each of the above tanks the following components. Emergency vents, primary vents, Morrison Brothers liquid level clock gauge, Morrison Brothers overfill protection valve, grade level fill piping complete with a 20 Gallon Spill Mate overspill container, 1-way swing check valve, ball valve, male adapter, dust cap and the required product identification & warning decals. 4.1.11 Furnish and install (2) 3 /4 HP Red Jacket ' Submersible Turbine Pump's (STP) complete with a 2" ball valve, 2" electric anti siphon valve, pressure relief valve and the required 2" rigid pipe and fittings to tie the new pumps into the existing aboveground piping. 4.1.12 Furnish and install (2) Mechanical Line Leak Detectors, 1 for each product line. 4.1.13 Pressure and soap test the new piping. 4.1.14 Install in each tank (1) Veeder-Root in tank liquid level probe and (1) Veeder-Root interstitial sensor. 4.1.15 Connect the new VR probes and sensors to the existing VR console with the required conduit, seal offs & junction boxes as needed on each tank. 4.1.16 Re- program the VR console as needed. 4.1.17 Provide conduit and wiring as needed to connect the new Red Jacket STP's and the electric anti siphon valves. 4.1.18 After fuel has been delivered Vendor will start up and test the pumps for proper operation. 4.1.19 Have a 3rd party do a precision test on the lines and leak detectors. 4.1.20 Leave the site clean and free of debris associated with the above scope of work.