Renovation of a conference / convention center in Raton, New Mexico. Working plans call for the renovation of a conference / convention center.

For a contract to replace doors and/or hardware on approximately ten exterior doors at the RATON CONVENTION CENTER located at 901 South Third Street in Raton, NM. Some doors will require low voltage electronic hardware. Submit questions or requests for bid documents to the office of the architect, Alpha Design, P.O. Box 241, Raton, NM 87740, phone 575-445-4235, email alphadesign@bacavalley.com. The City of Raton reserves the right to waive technicalities, accept or reject any or all bids as deemed to be in the best interest of the City of Raton. PROJECT SUMMARY Replace doors and/or hardware at approximately ten exterior doors, and related work. Some doors will require electronic hardware, card readers, and wiring. DOOR SCHEDULE Doors 1,2,3,4,5,6: Existing glazed hollow metal door and frame to remain. Remove cipher lock from door 4. Replace panic bar and surface bolts into head and sill with new. Remove astragal bar spanning the gap between each door pair. Each doors will act independently of its mate rather than latch to its mate. One door won't need to open before its mate opens as they currently do. Replace pulls with new. Replace closer with new. Patch/bondo holes and dents in door and frame. Sand, prime, and paint interior and exterior of door and frame. Replace weatherstripping and sweeps. Include brush weatherstripping between each pair. Replace hinges with ball bearing hinges to match existing. Leave threshold. Install new kick down stop at each door. New card reader and actuator at door 4, none at 1,2,3,5,6. Doors 7,8 : Existing glazed hollow metal door and frame to remain. Remove cipher lock from both doors. Replace panic bar with new. Replace pulls with new. Replace closer with new. Patch/bondo holes and dents in door and frame. Sand, prime, and paint interior and exterior of door and frame including sidelite. Replace weatherstripping and sweeps. Replace hinges with ball bearing hinges to match existing. Leave threshold. Install new kick down stop at each door. New card reader and actuator at door 8, none at 7. At the sidelite between doors 7 and 8 the hollow metal frame is rusted near the sidewalk. Install 2"x1.5"x1/8" or appropriately sized steel angle approximately 10" long over existing frame to cover rusted vertical and horizontal face of the hollow metal frame outside of the glass. Screw to old frame. Replace the rusted hollow metal glass stop measuring approximately 1/2 "x 1/2 "x 10". Replace the sleeve anchors from the existing aluminum threshold into the concrete floor slab at door 8 so that the threshold is firmly anchored. Doors 9,10: Existing hollow metal door and frame to remain. Doors measure approximately 46" x 89" each. Field measure. Existing frame includes a fixed interior mullion between the doors. Door 9 remove panic bar from interior and pull with thumb lever from exterior. Door 9 install re-used panic bar from door 10. No card reader or actuator required. Neatly weld plate over old pull location at exterior. Sand, prime, and paint exterior of doors and frame. Door 10 new push bar with actuator and card reader. Salvage old push bar for re-use. New closers. Patch/bondo holes and dents in door and frame. Sand, prime, and paint interior and exterior of doors and frame. New weatherstripping and sweeps. Leave hinges and threshold. Install new kick down stop at each door. Doors 11,12: Existing hollow metal interior door and frame to remain. Door 11 replace existing faulty flush bolts which are recessed into the door edge. Door 12 replace cipher lever lock with new lever hardware with actuator and card reader. Patch/bondo holes and dents in door and frame. Sand, prime, and paint each side of doors and frame. No closers or thresholds present or required. Doors 13,14 : Existing glazed hollow metal door and frame to remain. Remove pull with thumb lever from exterior of both doors. Leave interior push bars, closers, threshold, weatherstripping, hinges. Neatly weld plate over old pull locations at exterior. Patch/bondo holes and dents in door and frame. Sand, prime, and paint exterior of door and frame. No card reader required. HOLLOW METAL DOORS AND FRAMES