Remodeling and renovation of a service station / car wash facility in Stockton, California. Working plans call for the remodel of a service station / car wash facility; and for the renovation of a service station / car wash facility.

**As of July 23, 2025, bids were canceled. No definite date for the rebid.** Questions regarding this IFPQ must be submitted in writing. Bidders are encouraged to submit their written questions by 3:00 p.m. on May 20, 2025. B. Written questions must include the individual's name, firm name, complete address, and must reference IFPQ No. 10A2739. Questions must be sent to the following email: Email: Tiaja.Watson@dot.ca.gov an estimated value of greater than $5,000.00, but not more than $461,000.00 This Agreement will commence on June 30, 2025 (estimate) This Agreement will expire on June 29, 2026 (estimate) Contractor shall remove, replace, and legally dispose of existing bathroom partitions, fixtures, toilets, urinals, sinks, mirrors, base board, urinal dividers, doors, and toilet partitions. 1) Stockton Maintenance Station (MS) - Building B-2 -Men's Bathroom (refer to Attachment 3,Stockton B-2 Men's Bathroom Photos) a) Contractor shall remove and legally dispose of the following existing items: i. One (1) urinal. ii. iii. iv. v. vi. vii. viii. ix. x. xi. xii. xiii. One (1) urinal partition. One (1) sink. One (1) toilet. One (1) toilet partition and partition door. One (1) Mirror. One (1) soap dispenser. One (1) paper towel dispenser. Two (2) grab bars. One (1) toilet seat cover dispenser. One (1) bathroom closet. One (1) light switch. Approximately 38 feet (ft) x four (4) ft of Fiberglass Reinforced Plastic wall panels. b) Contractor shall furnish and install the following new items: i. One (1) new toilet with a flush valve. Toilet shall be a Sloan Efficiency _ 1.1_1.28_1.6 Gallons per flush, elongated bowl, top spud, or equivalent. ii. iii. iv. v. vi. vii. viii. ix. x. xi. xii. One (1) new washout urinal & automatic flush valve; Sloan ECOS(R), 0.25 Gallons per flush, or equivalent. One (1) new Slab-Edge Solid Surface Bathroom Trough Sink 30 inches (") (30"), or equivalent. One (1) new commercial grade soap dispenser. One (1) new commercial grade toilet paper dispenser. One (1) new commercial grade toilet seat cover dispenser. One (1) new commercial grade paper towel dispenser after walls have been completed. One (1) new Bobrick_ Welded-Frame Mirror, or equivalent, measuring 24" wide x 36" high. Fiberglass Reinforced Plastic wall panels four (4) ft high measured from the floor level on all inside bathroom walls. Urinal stainless-steel partition measuring approximately 56" x 58". Bathroom stainless- steel partition measuring approximately 56" x 58" (partition) and approximately 58" x 33.5" (partition door). Two (2) electrical power outlets. xiii. xiv. xv. xvi. One (1) new Ground Fault Circuit Interrupter (GFCI) receptacle and stainless-steel cover plate. Two (2) new grab bars. One (1) bathroom closet. One (1) light switch. c) Contractor shall seal all cracks and apply an epoxy vapor barrier primer with a polyaspartic urethane topcoat with epoxy flakes to floor and four (4) feet high on walls. Flakes color shall be of Caltrans Contract Manager's choice. d) Contractor shall paint all interior walls with moisture-resistant paint. Contractor shall apply a prime and sealant and paint to walls. e) Contractor shall clean existing floor to remove and legally dispose of remaining paint on floor. f) Bathroom measurements are approximately nine (9) ft x 11 ft. 2) Stockton MS - Building B-2 - Men's & Women's Bathroom (refer to Attachment 4, Stockton B-2 Men's and Women's Bathroom Photos) One (1) sink. a) Contractor shall remove and legally dispose of the following existing items: i. ii. iii. One (1) toilet. One (1) Mirror. iv. One (1) soap dispenser. v. One (1) paper towel dispenser. vi. Two (2) grab bars. vii. One (1) toilet seat cover dispenser. viii. Two (2) bathroom closets. ix. One (1) light switch. x. Approximately 29 ft x four (4) ft of Fiberglass Reinforced Plastic wall panels. b) Contractor shall furnish and install the following new items: i. One (1) new toilet with a flush valve. Toilet shall be a Sloan Efficiency _ 1.1_1.28_1.6 Gallons per flush, elongated bowl, top spud, or equivalent. ii. iii. One (1) new Slab-Edge Solid Surface Bathroom Trough Sink 30", or equivalent. One (1) new commercial grade soap dispenser. iv. One (1) new commercial grade toilet paper dispenser. v. One (1) new commercial grade toilet seat cover dispenser. vi. One (1) new commercial grade paper towel dispenser after walls have been completed. vii. One (1) new Bobrick_ Welded-Frame Mirror, or equivalent, measuring 24" wide x 36" high. viii. Fiberglass Reinforced Plastic wall panels four (4) ft high measured from the floor level on all inside bathroom walls. ix. One (1) new Ground Fault Circuit Interrupter (GFCI) receptacle and stainless-steel cover plate. x. Two (2) new grab bars. xi. Two (2) bathroom closets. xii. One (1) light switch. c) Contractor shall seal all cracks and apply an epoxy vapor barrier primer with a polyaspartic urethane topcoat with epoxy flakes to floor and four feet (4') high on walls. Flakes color shall be of Caltrans Contract Manager's choice. d) Contractor shall paint all interior walls with moisture-resistant paint. Contractor shall apply a prime and sealant and paint to walls. e) Contractor shall clean existing floor to remove and legally dispose of remaining paint on floor. f) Bathroom measurements are approximately eight (8) ft x seven (7) ft. 3) Stockton MS - Building B-6 - Men's Bathroom (refer to Attachment 5, Stockton B-6 Men's Bathroom Photos) Two (2) toilets a) Contractor shall remove and legally dispose of the following existing items: i. ii. iii. Two (2) bathroom partitions. Two (2) bathroom partition doors. iv. Two (2) urinals. v. Two (2) urinal partitions. vi. One (1) light switch. vii. Two (2) sinks. viii. Two (2) Mirrors. ix. Two (2) soap dispensers. x. One (1) paper towel dispenser. xi. One (1) power outlet. xii. One (1) bathroom closet. xiii. Two (2) toilet paper dispensers. xiv. Two (2) toilet seat cover dispensers. xv. One (1) bathroom window. xvi. One (1) bathroom door and frame. xvii. Bathroom vinyl flooring material. xviii. Bathroom fiberglass wall sheets, four (4) ft high. b) Contractor shall furnish and install the following new items: i. Two (2) toilets with a flush valve. Toilet shall be a Sloan Efficiency _ 1.1_1.28_1.6 Gallons per flush, elongated bowl, top spud, or equivalent. ii. iii. Two (2) stainless-steel bathroom partition and partition doors (73" x 28" x 57"). Two (2) washout urinals & automatic flush valves; Sloan ECOS(R), 0.25 Gallons per flush, or equivalent. iv. Two (2) stainless-sleet urinal partitions (18" x 42"). v. Two (2) Slab-Edge Solid Surface Bathroom Trough Sinks 30", or equivalent. vi. Two (2) Bobrick_ Welded-Frame Mirrors, or equivalent, measuring 24" wide x 36" high. vii. Two (2) commercial grade soap dispensers. viii. One (1) commercial grade paper towel dispenser. ix. One (1) power outlet. x. One (1) light switch. xi. Two (2) commercial grade toilet paper dispensers. xii. Two (2) commercial grade toilet seat cover dispensers. xiii. One (1) bathroom window and frame (44" x 48") similar quality to existing window, or better. xiv. One (1) bathroom door and frame (approximate door measurements are 32" x 79.5"). xv. One (1) bathroom door sign. xvi. Bathroom vinyl flooring material (approximate floor dimensions are 12 ft x nine (9) ft). Extend vinal flooring material at least four inches (4") above floor level. Contractor shall use Luxury Vinyl Plank (LVP), or equivalent, at least 0.080 inches thick with heat-welded seams. xvii. Two (2) new electrical power outlets. xviii. One (1) new Ground Fault Circuit Interrupter (GFCI) receptacle and stainless-steel cover plate. xix. Two (2) new grab bars. xx. One (1) bathroom closet xxi. Fiberglass Reinforced Plastic wall panels 4 ft high measured from the floor level on all inside bathroom walls. c) Contractor shall seal all cracks and apply an epoxy vapor barrier primer with a polyaspartic urethane topcoat with epoxy flakes to floor and four feet (4') high on walls. Flakes color shall be of Caltrans Contract Manager's choice. d) Contractor shall paint all interior walls with moisture-resistant paint. Contractor shall apply a prime and sealant and paint to walls e) Contractor shall clean existing floor to remove and legally dispose of remaining paint on floor. f) Bathroom measurements are approximately 12 ft x nine (9) ft. 4) Stockton MS - Building B-6 - Men's & Women's Bathroom (refer to Attachment 6, Stockton B-6 Men's and Women's Bathroom Photos) a) Contractor shall remove and legally dispose of the following existing items: i. One (1) toilet ii. iii. One (1) bathroom partition. One (1) bathroom partition door. iv. One (1) light switch. v. One (1) sink. vi. One (1) Mirror. vii. One (1) soap dispenser. viii. One (1) paper towel dispenser. ix. One (1) power outlet. x. One (1) bathroom closet. xi. One (1) toilet paper dispenser. xii. One (1) toilet seat cover dispenser. xiii. One (1) bathroom door and frame. xiv. Bathroom vinyl flooring material. xv. Bathroom fiberglass wall sheets (4 ft high). b) Contractor shall furnish and install the following new items: i. One (1) toilet with a flush valve. Toilet shall be a Sloan Efficiency _ 1.1_1.28_1.6 Gallons per flush, elongated bowl, top spud, or equivalent. ii. iii. One (1) stainless-steel bathroom partition and partition door (approximate partition measurements are five (5) ft x five (5) ft and approximate partition door measurements are 26" x 57"). One (1) Slab-Edge Solid Surface Bathroom Trough Sink 30", or equivalent. iv. One (1) Bobrick_ Welded-Frame Mirror, or equivalent, measuring 24" wide x 36" high. v. One (1) commercial grade soap dispenser. vi. One (1) commercial grade paper towel dispenser. vii. One (1) power outlet. viii. One (1) light switch. ix. One (1) commercial grade toilet paper dispenser. x. One (1) commercial grade toilet seat cover dispenser. xi. One (1) bathroom door and frame (approximate door measurements are 32" x 79"). xii. One (1) bathroom door sign. xiii. Bathroom vinyl flooring material (approximate floor dimensions are six (6) ft x seven (7) ft). Extend vinal flooring material at least four inches (4") above floor level. Contractor shall use Luxury Vinyl Plank (LVP), or equivalent, at least 0.080 inches thick with heat-welded seams. xiv. One (1) new electrical power outlet. xv. One (1) new Ground Fault Circuit Interrupter (GFCI) receptacle and stainless-steel cover plate. xvi. Two (2) new grab bars. xvii. Fiberglass Reinforced Plastic wall panels four (4) ft high measured from the floor level on all inside bathroom walls. c) Contractor shall seal all cracks and apply an epoxy vapor barrier primer with a polyaspartic urethane topcoat with epoxy flakes to floor and four feet (4') high on walls. Flakes color shall be of Caltrans Contract Manager's choice. d) Contractor shall paint all interior walls with moisture-resistant paint. Contractor shall apply a prime and sealant and paint to walls. e) Contractor shall clean existing floor to remove and legally dispose of remaining paint on floor. f) Bathroom measurements are approximately six (6) ft x seven (7) ft. 5) Stockton MS - Building B-8 - Men's Bathroom (refer to Attachment 7, Stockton B-8 Bathroom Photos) a) Contractor shall remove and legally dispose of the following existing items: i. One (1) door and frame ii. iii. One (1) urinal One (1) sink iv. One (1) soap dispenser v. One (1) paper towel dispenser vi. One (1) Mirror vii. Approximately 24 ft long X seven (7) ft high wooden wall b) Contractor shall furnish and install the following new items:i. ii. iii. One (1) wooden door and frame. Door size measurement is 35-5/8" wide x 79-5/8" high. One (1) toilet with a flush valve. Toilet shall be a Sloan Efficiency _ 1.1_1.28_1.6 Gallons per flush, elongated bowl, top spud, or equivalent. One (1) toilet flange. iv. One (1) new washout urinal & automatic flush valve; Sloan ECOS(R), 0.25 Gallons per flush, or equivalent. v. One (1) Slab-Edge Solid Surface Bathroom Trough Sink 30", or equivalent. vi. One (1) commercial grade soap dispenser. vii. One (1) commercial grade toilet paper dispenser. viii. One (1) commercial grade toilet seat cover dispenser. ix. One (1) commercial grade paper towel dispenser after walls have been completed. x. One (1) Bobrick_ Welded-Frame Mirror, or equivalent, measuring 24" wide x 36" high. xi. One (1) changing bench. xii. One (1) commercial grade exhaust fan. xiii. One (1) adequate lighting, lighting fixtures, and one (1) light switch. xiv. Approximately 26 ft X seven (7) ft (length X height) wooden wall. xv. Approximately eight (8) ft X 10 ft wooden ceiling. xvi. Two (2) new electrical power outlets. xvii. One (1) new Ground Fault Circuit Interrupter (GFCI) receptacle and stainless-steel cover plate. xviii. Two (2) new grab bars. xix. One (1) bathroom closet xx. One (1) bathroom door sign. xxi. Fiberglass Reinforced Plastic wall panels four (4) ft high measured from the floor level on all inside bathroom walls. c) Contractor shall paint all newly installed walls and ceiling with moisture-resistant paint. Contractor shall apply a prime and sealant and paint to walls and ceiling. Contractor shall apply a prime and paint to walls and ceiling. d) Contractor shall clean concrete floor to remove and legally dispose of remaining paint on floor. e) Bathroom measurements are approximately eight (8) ft X 10 ft. f) Contractor shall connect the newly installed bathroom fixtures with the adjacent sewer main line using a four-inch (4") diameter pipe. Approximate length is 50 ft from the new bathroom to the main sewer line. *The value for this project is based on a financial range. The value is listed as the highest possible cost from the range provided by a stakeholder or official project document.